AEG Sensorlogic Freestanding 60cm Dishwasher Stainless Steel F56302M0 Product - Page 19

The washing and drying results are not satisfactory

Page 19 highlights

ENGLISH 19 12.1 The washing and drying results are not satisfactory Problem Possible cause and solution Poor washing results. • Refer to "Daily use", "Hints and tips" and basket loading leaflet. • Use more intensive washing programmes. • Clean spray arm jets and filter. Refer to "Care and Cleaning". Poor drying results. • Tableware has been left for too long inside a closed appliance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level. • Plastic items may need to be towel dried. • For the best drying performance activate the option XtraDry. • We recommend to always use rinse aid, even in com- bination with multi-tablets. There are whitish streaks or bluish layers on glasses and dishes. • The release quantity of rinse aid is too much. Adjust the rinse aid level to a lower level. • The quantity of detergent is too much. There are stains and dry water • The released quantity of rinse aid is not sufficient. Ad- drops on glasses and dishes. just the rinse aid level to a higher level. • The quality of the rinse aid can be the cause. The dishes are wet. • For the best drying performance activate the option XtraDry. • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty. • The quality of the rinse aid can be the cause. • The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and use rinse aid and multi-tablets together. • Keep the dishwasher door ajar for some time before removing tableware. The interior of the appliance is • This is not a defect of the appliance. it is caused by wet. the humidity in the air that condenses on the walls. Unusual foam during washing. • Use the detergent for dishwashers only. • There is a leak in the rinse aid dispenser. Contact an Authorised Service Centre. Traces of rust on cutlery. • There is too much salt in the water used for washing. Refer to "The water softener". • Silver and stainless steel cutlery were placed together. Avoid to put silver and stainless steel items close together.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24

12.1
The washing and drying results are not satisfactory
Problem
Possible cause and solution
Poor washing results.
Refer to
"Daily use"
,
"Hints and tips"
and basket
loading leaflet.
Use more intensive washing programmes.
Clean spray arm jets and filter. Refer to
"Care and
Cleaning"
.
Poor drying results.
Tableware has been left for too long inside a closed
appliance.
There is no rinse aid or the dosage of rinse aid is not
enough. Set the rinse aid dispenser to a higher level.
Plastic items may need to be towel dried.
For the best drying performance activate the option
XtraDry.
We recommend to always use rinse aid, even in com-
bination with multi-tablets.
There are whitish streaks or
bluish layers on glasses and
dishes.
The release quantity of rinse aid is too much. Adjust
the rinse aid level to a lower level.
The quantity of detergent is too much.
There are stains and dry water
drops on glasses and dishes.
The released quantity of rinse aid is not sufficient. Ad-
just the rinse aid level to a higher level.
The quality of the rinse aid can be the cause.
The dishes are wet.
For the best drying performance activate the option
XtraDry.
The programme does not have a drying phase or has
a drying phase with low temperature.
The rinse aid dispenser is empty.
The quality of the rinse aid can be the cause.
The quality of the multi-tablets can be the cause. Try a
different brand or activate the rinse aid dispenser and
use rinse aid and multi-tablets together.
Keep the dishwasher door ajar for some time before
removing tableware.
The interior of the appliance is
wet.
This is not a defect of the appliance. it is caused by
the humidity in the air that condenses on the walls.
Unusual foam during washing.
Use the detergent for dishwashers only.
There is a leak in the rinse aid dispenser. Contact an
Authorised Service Centre.
Traces of rust on cutlery.
There is too much salt in the water used for washing.
Refer to
"The water softener"
.
Silver and stainless steel cutlery were placed together.
Avoid to put silver and stainless steel items close to-
gether.
ENGLISH
19