Acer Aspire 3810T Acer Aspire 3810T and Aspire 3810TZ Serivce Guide - Page 72

Error Message List - inverter

Get Acer Aspire 3810T PDF manuals and user guides View all Acer Aspire 3810T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Error Messages Invalid System Configuration Data I/O device IRQ conflict Operating system not found FRU/Action in Sequence BIOS ROM System board Run "Load Default Settings" in BIOS Setup Utility. RTC battery System board Enter Setup and see if fixed disk and drive A: are properly identified. Diskette drive Hard disk drive System board Error Message List No beep Error Messages No beep, power-on indicator turns off and LCD is blank. No beep, power-on indicator turns on and LCD is blank. No beep, power-on indicator turns on and LCD is blank. But you can see POST on an external CRT. No beep, power-on indicator turns on and a blinking cursor shown on LCD during POST. No beep during POST but system runs correctly. FRU/Action in Sequence Power source (battery pack and power adapter). See "Power System Check" on page 61. Ensure every connector is connected tightly and correctly. Reconnect the DIMM. LED board. System board. Power source (battery pack and power adapter). See "Power System Check" on page 61. Reconnect the LCD connector Hard disk drive LCD inverter ID LCD cable LCD Inverter LCD System board Reconnect the LCD connectors. LCD inverter ID LCD cable LCD inverter LCD System board Ensure every connector is connected tightly and correctly. System board Speaker System board 66 Chapter 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
66
Chapter 4
Error Message List
Invalid System Configuration Data
BIOS ROM
System board
I/O device IRQ conflict
Run “Load Default Settings” in BIOS Setup
Utility.
RTC battery
System board
Operating system not found
Enter Setup and see if fixed disk and drive A:
are properly identified.
Diskette drive
Hard disk drive
System board
No beep Error Messages
FRU/Action in Sequence
No beep, power-on indicator turns off and LCD
is blank.
Power source (battery pack and power
adapter). See “Power System Check” on page
61.
Ensure every connector is connected tightly
and correctly.
Reconnect the DIMM.
LED board.
System board.
No beep, power-on indicator turns on and LCD
is blank.
Power source (battery pack and power
adapter). See “Power System Check” on page
61.
Reconnect the LCD connector
Hard disk drive
LCD inverter ID
LCD cable
LCD Inverter
LCD
System board
No beep, power-on indicator turns on and LCD
is blank. But you can see POST on an external
CRT.
Reconnect the LCD connectors.
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
No beep, power-on indicator turns on and a
blinking cursor shown on LCD during POST.
Ensure every connector is connected tightly
and correctly.
System board
No beep during POST but system runs
correctly.
Speaker
System board
Error Messages
FRU/Action in Sequence