Alpine CDE-W265BT Owner's Manual (english) - Page 10

Initial System Start-Up, Adjusting Volume, Setting the Dimmer Control, Setting Time - clock

Get Alpine CDE-W265BT PDF manuals and user guides View all Alpine CDE-W265BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Attaching Setting the Dimmer Control Notes • Before attaching the front panel, make sure that there is no dirt or dust on the connector terminals and no foreign object between the front panel and the main unit. • Attach the front panel carefully, holding the sides of the front panel to avoid pushing buttons by mistake. Initial System Start-Up Be sure to press the RESET switch when using the unit for the first time, after changing the car battery, etc.  CDE-W265BT RESET switch  CDE-164BT RESET switch Adjusting Volume Turn the Rotary encoder until the desired sound is obtained. Press and hold DIM. for at least 2 seconds repeatedly to select the DIMMER mode. DIMMER AUTO  DIMMER ON  DIMMER OFF  DIMMER AUTO DIMMER AUTO mode: Decrease the illumination brightness of the unit's buttons with the head lights of the vehicle ON. This mode decreases the unit's backlighting in sync with headlight usage. DIMMER ON mode: Keep the illumination brightness of the backlighting dimmed. DIMMER OFF mode: Keep the illumination brightness of the backlighting bright. Note • The setting items are the same as DISPLAY setting in SETUP mode. For details, refer to "Dimmer Control" on page 29. Setting Time 1 Press and hold YSETUP for at least 2 seconds to activate the SETUP selection mode. 2 Turn the Rotary encoder to select GENERAL, and then press ENTER. 3 Turn the Rotary encoder to select the CLOCK ADJ mode, and then press ENTER. The time indication will blink. 4 Turn the Rotary encoder to adjust the hours while the time indication is blinking. 5 When the hour has been adjusted, press ENTER. 6 Turn the Rotary encoder to adjust the minutes while the time indication is blinking. 7 Press and hold YSETUP for at least 2 seconds to return to normal mode. Notes • To synchronize the clock to another clock/watch or radio time announcement, press and hold ENTER for at least 2 seconds after setting the "hour". Minutes will reset to "00". If the display shows over "30" minutes when you do this, the time will advance one hour. • Pressing t will return to the previous mode. • If no operation is performed for 60 seconds, the unit will return to normal mode automatically. 10-EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
10
-EN
Notes
•
Before attaching the front panel, make sure that there is no dirt or dust
on the connector terminals and no foreign object between the front
panel and the main unit.
•
Attach the front panel carefully, holding the sides of the front panel to
avoid pushing buttons by mistake.
Initial System Start-Up
Be sure to press the
RESET
switch when using the unit for the first time,
after changing the car battery, etc.
CDE-W265BT
CDE-164BT
Adjusting Volume
Turn the
Rotary encoder
until the desired sound is
obtained.
Setting the Dimmer Control
Press and hold
DIM.
for at least 2 seconds repeatedly to
select the DIMMER mode.
DIMMER AUTO
DIMMER ON
DIMMER OFF
DIMMER AUTO
DIMMER AUTO mode:
Decrease the illumination brightness of the unit’s buttons with the
head lights of the vehicle ON. This mode decreases the unit’s
backlighting in sync with headlight usage.
DIMMER ON mode:
Keep the illumination brightness of the backlighting dimmed.
DIMMER OFF mode:
Keep the illumination brightness of the backlighting bright.
Note
•
The setting items are the same as DISPLAY setting in SETUP mode.
For details, refer to “Dimmer Control” on page 29.
Setting Time
1
Press and hold
Y
SETUP
for at least 2 seconds to
activate the SETUP selection mode.
2
Turn the
Rotary encoder
to select GENERAL, and then
press

ENTER
.
3
Turn the
Rotary encoder
to select the CLOCK ADJ mode,
and then press

ENTER
.
The time indication will blink.
4
Turn the
Rotary encoder
to adjust the hours while the
time indication is blinking.
5
When the hour has been adjusted, press

ENTER
.
6
Turn the
Rotary encoder
to adjust the minutes while the
time indication is blinking.
7
Press and hold
Y
SETUP
for at least 2 seconds to return
to normal mode.
Notes
•
To synchronize the clock to another clock/watch or radio time
announcement, press and hold

ENTER
for at least 2 seconds after
setting the “hour”. Minutes will reset to “00”. If the display shows over
“30” minutes when you do this, the time will advance one hour.
•
Pressing
t
will return to the previous mode.
•
If no operation is performed for 60 seconds, the unit will return to
normal mode automatically.
Attaching
RESET switch
RESET switch