Alpine CDE-W265BT Owner's Manual (english) - Page 51
No Support, No Usb Device, No File - reset
View all Alpine CDE-W265BT manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 51 highlights
• The CD is being improperly inserted. - Make sure the CD is being inserted following instructions in the CD Player Operation section. Unable to fast forward or backward the CD. • The CD has been damaged. - Eject the CD and discard it; using a damaged CD in your unit can cause damage to the mechanism. CD playback sound skips due to vibration. • Improper mounting of the unit. - Securely re-mount the unit. • The disc is very dirty. - Clean the disc. • The disc has scratches. - Change the disc. • The pick-up lens is dirty. - Do not use a commercially available lens cleaner disc. Consult your nearest Alpine dealer. CD playback sound skips without vibration. • The disc is dirty or scratched. - Clean the disc; damaged disc should be replaced. Error displays (built-in CD player only). • Mechanical error - Press . After the error indication disappears, insert the disc again. If the above-mentioned solution does not solve the problem, consult your nearest Alpine dealer. CD-R/CD-RW playback not possible. • Close session (finalization) has not been performed. - Perform finalization and attempt playback again. MP3/WMA MP3 or WMA is not played back. • Writing error occurred. The MP3/WMA format is not compatible. - Make sure the MP3/WMA has been written in a supported format. Refer to "About MP3/WMA" on page 15, then rewrite in the format supported by this device. Audio The sound is not output from the speakers. • Unit has no output signal of the internal amplifier. - POWER IC is switched to "ON", refer to "Connecting to an External Amplifier (POWER IC)" on page 19. iPod iPod does not play and no sound is output. • The iPod has not been recognized. - Reset this unit and the iPod. Refer to "Initial System Start-Up" on page 10. To reset the iPod, refer to the Owner's Manual of the iPod. Indication for CD Player • Mechanism error. 1 Press the button and eject the CD. If not ejecting, consult your Alpine dealer. 2 When the error indication remains after ejecting, press the button again. If the error indication still does not turn off after pressing the button, consult your Alpine dealer. • When "ERROR" is displayed: If the disc cannot be ejected by pressing , press the RESET switch (refer to "Initial System Start-Up" on page 10) and press again. If the disc still cannot be ejected, consult your Alpine dealer. • A copy-protected WMA file was played back. - You can only play back non-copy-protected files. • A sampling rate/bit rate not supported by the unit is used. - Use a sampling rate/bit rate that is supported by the unit. NO SUPPORT • An AAC format disc is inserted. - Change to a disc of a supported format. • Text information that is not recognizable by the unit is being used. - Change the text information to text that is supported by the unit. Indication for Flash Memory • Communication error or other error. - You can solve the problem by switching the source, turning ACC off/on, or turning power off/on. • Communication error. - You can solve the problem by switching the source, turning ACC off/on, or turning power off/on. • Abnormal current is run to the USB Flash Memory device. - You can solve the problem by turning ACC off/on, or turning power off/on. • No CD is inserted. - Insert a CD. • Although a disc is inserted, "NO DISC" is displayed and the unit does not start to play or eject the disc. - Remove the disc by pressing : If the disc cannot be ejected by pressing , press the RESET switch (refer to "Initial System Start-Up" on page 10) and press again. If the disc still cannot be ejected, consult your Alpine dealer. NO USB DEVICE • A Flash Memory is not connected. - Make sure the Flash Memory device is correctly connected. NO FILE • No song (file) is stored in the Flash Memory. - Connect the Flash Memory device after storing songs (files). 51-EN