Alpine INA-W910 Owner's Manual (english) - Page 64

Adjusting the Touch Panel, Display On and Off, GENERAL Setup, General Setup Operation

Get Alpine INA-W910 PDF manuals and user guides View all Alpine INA-W910 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Adjusting the Touch Panel Adjustment becomes necessary when the display position on the LCD and the touch position on the touch panel do not match. Setting item: Screen Alignment Setting contents: / Reset 1 Touch [ ] of Screen Alignment. The adjustment screen appears. 2 Accurately touch the mark provided in the lower left corner of the screen. The screen changes to the adjustment screen. 3 Accurately touch the mark provided in the upper right corner of the screen. This completes adjustment, and returns to the Display setup mode screen. • If you have touched a location other than the mark, touch [Reset] to restore the adjustment screen to the initial setting. • If you touch [ ] on the adjustment screen, no adjustment is done and the Display setup screen is restored. Display On and Off You can turn off the screen display to reduce power consumption. This additional power enhances the sound quality. Setting item: Display Setting contents: OFF / ON • If any button on the unit is pressed during display off mode, the screen will be displayed for 5 seconds to show the operation before returning to display off mode. GENERAL Setup General Setup Operation To display the General Setup Menu screen: Your vehicle must be parked with the ignition key in the ACC or ON position. To do this, follow the procedures below. 1 Bring your vehicle to a complete stop at a safe location. Engage the parking brake. 2 Keep pushing the foot brake and release the parking brake once then engage it again. 3 When the parking brake is engaged for the second time, release the foot brake. • For automatic transmission vehicles, place the transmission lever in the Park position. Now, the locking system for the General mode operation has been released. Engaging the parking brake can reactivate the General Setup Menu, as long as the car's ignition has not been turned off. It is not necessary to repeat the above procedure (1 through 3) of "To display the General mode screen." Each time the ignition is turned OFF, perform the procedure of "To display the General mode screen." The following steps 1 to 5 are common operations to each "Setting item" of General Setup. Refer to each section for details. 1 Press SOURCE/ on the unit. The SOURCE selection screen is displayed. 2 Touch [ ] on the main source screen. The Setup Select screen is displayed. 3 Touch [ ] of General Setup. The General Setup screen appears. 4 Touch [ ] or [ ] of the desired item to change its setting. Setting items: Clock / Demonstration / Beep / Auto Scroll / Key Dimmer Level 5 Touch [ ] to return to the previous screen. Touch [Exit] to return to the main source screen that was displayed before the setup operation was started. • Immediately after changing the settings of General Mode (While the system is writing data automatically) do not turn the ignition key (engine key) to OFF. Otherwise, the settings may not be changed. 64-EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
64
-EN
Adjustment becomes necessary when the display position on the LCD
and the touch position on the touch panel do not match.
Setting item: Screen Alignment
Setting contents:
/ Reset
1 Touch
[
]
of Screen Alignment.
The adjustment screen appears.
2
Accurately touch the
mark provided in the lower left
corner of the screen.
The screen changes to the adjustment screen.
3
Accurately touch the
mark provided in the upper right
corner of the screen.
This completes adjustment, and returns to the Display
setup mode screen.
•
If you have touched a location other than the
mark, touch
[Reset]
to restore the adjustment screen to the initial setting.
•
If you touch
[
on the adjustment screen, no adjustment is done
and the Display setup screen is restored.
You can turn off the screen display to reduce power consumption.
This additional power enhances the sound quality.
Setting item: Display
Setting contents: OFF / ON
•
If any button on the unit is pressed during display off mode, the
screen will be displayed for 5 seconds to show the operation before
returning to display off mode.
General Setup Operation
1
Press
SOURCE/
on the unit.
The SOURCE selection screen is displayed.
2
Touch
[
]
on the main source screen.
The Setup Select screen is displayed.
3
Touch
[
]
of General Setup.
The General Setup screen appears.
4
Touch
[
]
or
[
]
of the desired item to change its
setting.
Setting items:
Clock / Demonstration / Beep / Auto Scroll / Key Dimmer Level
5
Touch
[
]
to return to the previous screen.
Touch
[
Exit
]
to return to the main source screen that was
displayed before the setup operation was started.
•
Immediately after changing the settings of General Mode (While the
system is writing data automatically) do not turn the ignition key
(engine key) to OFF. Otherwise, the settings may not be changed.
Adjusting the Touch Panel
Display On and Off
GENERAL Setup
To display the General Setup Menu screen:
Your vehicle must be parked with the ignition key in the ACC or
ON position. To do this, follow the procedures below.
1
Bring your vehicle to a complete stop at a safe
location. Engage the parking brake.
2
Keep pushing the foot brake and release the parking
brake once then engage it again.
3
When the parking brake is engaged for the second
time, release the foot brake.
•
For automatic transmission vehicles, place the transmission lever
in the Park position.
Now, the locking system for the General mode operation has
been released. Engaging the parking brake can reactivate the
General Setup Menu, as long as the car’s ignition has not been
turned off. It is not necessary to repeat the above procedure
(1 through 3) of “To display the General mode screen.”
Each time the ignition is turned OFF, perform the procedure of “To
display the General mode screen.”
The following steps 1 to 5 are common operations to each
“Setting item” of General Setup. Refer to each section for
details.