Alpine KTX-100EQ Owners Manual - Page 4

I.&. - windows 7

Get Alpine KTX-100EQ - IMPRINT Sound Tuning PDF manuals and user guides
UPC - 793276401519
View all Alpine KTX-100EQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

Before Setting MultEQ I.&. WARNING While driving, do not set up MultEQ. To prevent accidents, do not set up MultEQ while driving. The setting of the MultEQ function is required to mount the microphone in the vehicle in order to measure sound characteristics. Also, during measurement, loud measurement tone (signal) from the speakers may be output. Making such settings may distract you from driving and result in an accident. Read following provisions before setting MultEQ. The MultEQ setting should be made in as quiet a place as possible after turning off the engine, airconditioner and heater. If you have a car phone or cellular phone in the vehicle, remove them from the vehicle or turn its power off. If sound other than measurement tone to be measured (engine or receiving sound of car phone, etc.) occur, sound measurement in the vehicle may not be accurate. When setting MuItEQ, be sure to use the microphone supplied with this unit. If a microphone other than the supplied one is used, measurement may not be possible or sound measurement in the vehicle may not be accurate. If a power amplifier or a powered subwoofer with an input level control is connected and this level is lowered, measurement may not be possible. However, the input level should set lowered than normal level to adequately perform measurement. If a power amplifier with a low-pass filter is connected, measure MultEQ when the low-pass filter of the power amplifier is turned off. If a low-pass filter is built into the powered subwoofer or power amplifier for subwoofer, set the cut-off frequency to the highest value. If MultEQ is set and the function is turned on, MX, X-OVER, Time Correction, User's EQ, Parametric EQ and Graphic EQ are automatically adjusted. Therefore, they cannot be individually adjusted. After you have stored the result of MultEQ you adjusted in the CDA-9887/CDA-9887R, if you store the results of MultEQ again in the CDA-9887/CDA-9887R, the previously stored MultEQ will be completely cleared and replaced by the new one. Setting MultEQ 1 Prepare for MultEQ setting. • Park the vehicle in a quiet location. • Close doors, windows, sunroof, etc. • Turn off the engine of the vehicle. • Set the air-conditioner and heater to OFF. 2 Set the key position of the vehicle to ACC or turn it on. • If an air-conditioner or heater is turned on, turn it off. Measurement should not be performed if air-conditioner or heater noise is present.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
Before
Setting
MultEQ
I.&.
WARNING
While
driving,
do
not
set
up
MultEQ.
To prevent accidents, do not set up MultEQ while driving. The setting
of
the MultEQ
function
is
required to mount the microphone
in
the vehicle
in
order to measure sound
characteristics. Also, during measurement, loud measurement tone (signal) from the
speakers may be output. Making such settings may distract you from driving and result
in
an
accident.
Read
following
provisions
before
setting
MultEQ.
The MultEQ setting should be made
in
as quiet a place
as
possible after turning off the engine, air-
conditioner and heater. If you have a car phone or cellular phone
in
the vehicle, remove them from the
vehicle
or
turn its power off.
If
sound other than measurement tone to be measured (engine or receiving
sound
of
car phone, etc.) occur, sound measurement
in
the vehicle may not be accurate.
When setting MuItEQ, be sure to use the microphone supplied with this unit.
If
a microphone other than
the supplied one
is
used, measurement may not be possible or sound measurement
in
the vehicle may not
be accurate.
If a power amplifier
or
a powered subwoofer with an input level control
is
connected and this level is
lowered, measurement may not be possible. However, the input level should set lowered than normal
level to adequately perform measurement.
If a power amplifier with a low-pass filter is connected, measure MultEQ when the low-pass filter
of
the
power amplifier is turned off. If a low-pass filter
is
built into the powered subwoofer
or
power amplifier
for subwoofer, set the cut-off frequency to the highest value.
If
MultEQ
is
set and the function
is
turned on, MX, X-OVER, Time Correction, User's EQ, Parametric
EQ and Graphic EQ are automatically adjusted. Therefore, they cannot be individually adjusted.
After you have stored the result
of
MultEQ you adjusted
in
the CDA-9887/CDA-9887R, if you store the
results
of
MultEQ again
in
the CDA-9887/CDA-9887R, the previously stored MultEQ will be
completely cleared and replaced by the new one.
Setting
MultEQ
1
Prepare for MultEQ setting.
•
Park the vehicle
in
a quiet location.
•
Close doors, windows, sunroof, etc.
•
Turn
off the engine of the vehicle.
•
Set the air-conditioner and heater to
OFF.
2
Set the key position of the vehicle to ACC or turn it on.
•
If
an air-conditioner
or
heater
is
turned on, turn it off. Measurement should not be performed
if
air-conditioner
or
heater noise
is
present.