Ariens Power Brush 36 Owners Manual

Ariens Power Brush 36 Manual

Get Ariens Power Brush 36 PDF manuals and user guides View all Ariens Power Brush 36 manuals
Add to My Manuals
Save this manual to your list of manuals

Ariens Power Brush 36 manual content summary:

  • Ariens Power Brush 36 | Owners Manual - Page 1
    926 Series All Season Power Brush Owner/Operator Manual Manuel du Propriétaire/Utilisateur Model 926045 - PB36 ENGLISH FRANÇAIS 04219700B 8/10 Printed in USA
  • Ariens Power Brush 36 | Owners Manual - Page 2
    10 Maintenance 15 Service & Adjustments 19 Storage 27 Troubleshooting 28 Service Parts 28 Specifications 29 Warranty 30 INTRODUCTION NON-ENGLISH MANUALS Manuals in languages other than English may be obtained from your Dealer. Visit your dealer or www.ariens.com for a list of languages
  • Ariens Power Brush 36 | Owners Manual - Page 3
    been properly completed. NOTE: To locate your nearest Ariens Dealer, go to www.ariens.com on the internet. WARNING: Improper assembly or adjustments can cause serious injury. 2. Understand all Safety Precautions provided in the manuals. 3. Review control functions and operation of the unit. Do not
  • Ariens Power Brush 36 | Owners Manual - Page 4
    engine, and wait for all movement to stop before unclogging or working on brush. Keep hands and feet away from brush TRAINING Original purchaser of this unit was instructed by the seller on safe and proper rented or sold, ALWAYS provide this manual and any needed safety training before operation
  • Ariens Power Brush 36 | Owners Manual - Page 5
    all safety practices in Owner/Operator Manual before beginning assembly or operating. Failure to follow instructions could result in personal injury and/or damage to unit. ALWAYS remove key and/or wire from spark plug before assembly, maintenance or service. Unintentional engine start up can cause
  • Ariens Power Brush 36 | Owners Manual - Page 6
    unit parts which might be hot from operation. Allow parts to cool before attempting to maintain, adjust or service. engine, remove key and allow moving parts to stop before leaving operator's position. Read, understand, and follow all instructions in the manual and on the machine before starting
  • Ariens Power Brush 36 | Owners Manual - Page 7
    allow engine to cool before servicing. NEVER fill fuel tank when engine is running before filling. When practical, remove gas-powered equipment from the truck or trailer and Adjust brush height before operating. Refer to Operation. Before separating brush thoroughly. See Engine Manual for proper
  • Ariens Power Brush 36 | Owners Manual - Page 8
    Engine Manual for detailed instructions. Fill Engine Fuel Tank Refer to Engine Manual for proper fuel type and tank capacity. Refer to Filling Fuel Tank on page 13. Check Function of all Controls Ensure unit runs and performs properly. Refer to Operation on page 10. Run-in Attachment Belt 1. Start
  • Ariens Power Brush 36 | Owners Manual - Page 9
    Selector Lever 11.Height Adjustment 3. Attachment Clutch Wheels Lever 12.Fuel Shut Off Valve 4. Brush Angle Lock 13.Fuel Fill Cap Lever 14.Choke 5. Recoil Starter Handle 15.Oil Drain Plug 6. Engine Shut Off 4 Switch 16.Electric Start Pushbutton 7. Engine Throttle 17.Muffler 8. Oil
  • Ariens Power Brush 36 | Owners Manual - Page 10
    (1) to engage brush. Release clutch lever (2) to disengage power 1 to brush. IMPORTANT: If the belt squeals when the engine starts. Engine Shut-Off Switch (Figure 5) 1. Set the engine shut off switch (Figure 4, item 6) to the On position to start and operate the engine. 2. Set the engine
  • Ariens Power Brush 36 | Owners Manual - Page 11
    engine speed. To increase or decrease engine speed, adjust to: 1. Fast (normal or warm starts) to left 2. Part-Throttle at center 3. Slow (cold weather starts . Open Position: Use this position to run the unit. BRUSH ANGLE ADJUSTMENT Brush can be positioned either straight ahead or angled 20º to either
  • Ariens Power Brush 36 | Owners Manual - Page 12
    engine and allow all moving parts to stop. 5. Check the width of the swept area. The brush pattern should be 2-3 inches (5.08-7.6 cm) wide, running the length of the brush. See Figure 6. 6. To adjust, turn caster wheel support . If the engine experiences starting or performance problems after using a
  • Ariens Power Brush 36 | Owners Manual - Page 13
    Engine Manual for detailed instructions. TO STOP IN AN EMERGENCY Immediately release both control levers to stop unit in an emergency. Stop engine and wait for all rotating parts to stop before leaving operator's position. STARTING AND SHUT OFF IMPORTANT: At start-up, allow unit and engine to adjust
  • Ariens Power Brush 36 | Owners Manual - Page 14
    NOT operate starter more than 15 seconds per minute, as overheating and damage can occur. (If engine does not start, refer to Troubleshooting on page 28.) 7. Adjust choke as needed. 8. Disconnect power cord from outlet, then starter. Shut Off 1. Release attachment clutch lever (Figure 4, item 3) and
  • Ariens Power Brush 36 | Owners Manual - Page 15
    service or adjustments which may be required to keep your unit operating at peak efficiency. Should engine service be required, contact an Ariens dealer or an authorized engine manufacturer's service or service. Unintentional engine start up can cause death or serious injury. 2. Remove belt cover
  • Ariens Power Brush 36 | Owners Manual - Page 16
    unit back while guiding brush attachment up and onto lower pivot rod. 3. Tilt traction unit back up level to bring it together with brush attachment. 4. Install cap screws (one on each side at top) to secure brush attachment to traction unit. 5. Place attachment drive belts onto engine sheave. It
  • Ariens Power Brush 36 | Owners Manual - Page 17
    Manual for detailed instructions. Run engine just prior to changing oil. Warm oil will flow more freely and carry away more contamination. CHECK TIRE PRESSURE CAUTION: Avoid injury! Explosive separation of tire and rim parts is possible when they are serviced incorrectly: • Do not attempt to mount
  • Ariens Power Brush 36 | Owners Manual - Page 18
    allow grease or oil to get on friction disc, friction plate or belts. 2. Apply Hi-Temp Grease (Part Number 00036800) or equivalent to the lubrication fittings after the first 16 hours of use and every 8 hours thereafter. See Service Parts on page 28. 3. Apply a few drops of oil to the friction disc
  • Ariens Power Brush 36 | Owners Manual - Page 19
    SERVICE AND ADJUSTMENTS WARNING: AVOID INJURY. Read and understand the entire Safety pivot pin into hole. 5. Secure adjustment pivot pin with hairpin. 6. Make sure the speed selector shifts into each speed position. 7. Check forward and reverse speeds: a. Start unit. b. Shift speed selector into
  • Ariens Power Brush 36 | Owners Manual - Page 20
    clearance between the roller and the frame. 1. Place the unit into the service position (See Service Position on page 15). 2. With the clutch lever engaged, check the frame. Engine Sheave Attachment Drive Belts Frame Idler Adjustment Nut Attachment Idler Arm Roller Idler Pulley Adjustment Nut
  • Ariens Power Brush 36 | Owners Manual - Page 21
    engaged. See Figure 14. • If spring extension is within the specified range, go to Check Belt Finger Clearance on page 21. • If spring extension is outside of specified range, go to step 2. 2. To adjust belt finger, loosen the bolts and move the finger to the proper position. Tighten the bolts and
  • Ariens Power Brush 36 | Owners Manual - Page 22
    tighten the jam nut, and then hold the adjuster body with pliers and tighten the jam nut with wrench. 1 ATTACHMENT DRIVE BELTS REPLACEMENT WARNING: ALWAYS remove key and-or wire from spark plug before assembly, maintenance or service. Unintentional engine start up can cause death or serious injury
  • Ariens Power Brush 36 | Owners Manual - Page 23
    Engine Sheave Traction Drive Belt Idler Attachment Drive Belts Idler OS7196 Figure 18 4. Remove traction drive belt from drive plate assembly pulley. See Figure 19. 5. Install new traction drive belt (Part (2). 13. Adjust traction drive clutch (See Traction Drive Clutch Adjustment on page 21
  • Ariens Power Brush 36 | Owners Manual - Page 24
    Screws 3. Carrier 4. Spring Clip Pin 5. Hex Shaft 6. Bearing Flange 7. Pinion Sprocket Figure 19 BRUSH SEGMENT REPLACEMENT WARNING: ALWAYS remove key and/or wire from spark plug before assembly, maintenance or service. Unintentional engine start up can cause death or serious injury. 1. Shut off
  • Ariens Power Brush 36 | Owners Manual - Page 25
    Nyloc Nut End Plate Flanged Bearing Nyloc Nut U-Joint Figure 20 Brush End Support Brush Segment Splined Shaft Gearbox Figure 21 GB - 25
  • Ariens Power Brush 36 | Owners Manual - Page 26
    Install end plate on support shaft assembly and secure with three flanged head bolts. See Figure 22. 9. Position brush back down horizontally. 10. Repeat steps 5 through 8 to replace segments for opposite end of brush. 11. Manually move traction unit forward while guiding brush gearbox splined shaft
  • Ariens Power Brush 36 | Owners Manual - Page 27
    . To treat the fuel system for storage: 1. Add fuel stabilizer according to manufacturer's instructions. 2. Run engine for at least 10 minutes after adding stabilizer to allow it to reach the carburetor. NEVER store the engine with fuel in the fuel tank inside of a building with potential sources of
  • Ariens Power Brush 36 | Owners Manual - Page 28
    4. Replace or clean spark plug. Engine problems. 1. See Engine Manual. 1. See Engine Manual. Does not operate in Forward/ Reverse. 1. Friction disc not adjusted properly. 2. Traction belt not functioning. 1. Repair or replace friction disc. See Service and Adjustments on page 19. 2. Repair or
  • Ariens Power Brush 36 | Owners Manual - Page 29
    Fast Idle Speed-RPM 3800 ±100 Starter 120VAC Electric and Recoil Fuel See Engine Manual Tank Capacity - qts. (L) 6.3 (6.1) Clearing Width - in. (cm) 36 (91.44) Brush Diameter-in. (cm) 24 (60.1) Brush Rotation Speed - RPM 200 Drive (Traction Unit) Disc-O-Matic® Drive Speeds (Traction
  • Ariens Power Brush 36 | Owners Manual - Page 30
    register the unit online at www.ariens.com or www.gravely.com. To obtain warranty service, the original purchaser must: • Perform the maintenance and minor adjustments explained in the owner's manual. • Promptly notify Ariens or an authorized Ariens or Gravely service representative of the need for
  • Ariens Power Brush 36 | Owners Manual - Page 31
    Engines and engine accessories are covered only by the engine manufacturer's warranty and are not covered by this warranty. • Parts that are not genuine Ariens or Gravely service parts brushes, headlights, light bulbs, knives, cutters. • Any misuse, alteration, improper assembly, improper adjustment,
  • Ariens Power Brush 36 | Owners Manual - Page 32
    Ariens Company 655 West Ryan Street Brillion, WI 54110-1072 920-756-2141 Fax 920-756-2407 www.ariens.com
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
Owner/Operator Manual
Manuel du Propriétaire/Utilisateur
Model
926045 – PB36
926 Series All Season Power Brush
04219700B 8/10
Printed in USA
ENGLISH
FRANÇAIS