Asus A7V400-MX Motherboard DIY Troubleshooting Guide - Page 24

Product introduction, USB device wake-up 3-pin USBPWR12, USBPWR34, USBPWR56

Get Asus A7V400-MX PDF manuals and user guides View all Asus A7V400-MX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

2. USB device wake-up (3-pin USBPWR12, USBPWR34, USBPWR56) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 sleep mode (no power to CPU, DRAM in slow refresh, power supply in reduced power mode). Both jumpers are set to pins 1-2 (+5V) by default because not all computers have the appropriate power supply to support this feature. The USBPWR12 and USBPWR34 jumpers are for the rear USB ports. USBPWR56 is for the internal USB connector. • The USB device wake-up feature requires a power supply that can provide 500mA on the +5VSB lead for each USB port. Otherwise, the system does not power up. • The total current consumed must NOT exceed the power supply capability (+5VSB) whether under normal condition or in sleep mode. A7V400-MX A7V400-MX USB Device Wake Up USBPWR12 USBPWR34 2 1 +5V 3 2 +5VSB (Default) USBPWR56 12 23 +5V +5VSB (Default) 1-14 Chapter 1: Product introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
1-14
Chapter 1:
Product introduction
2.
USB device wake-up (3-pin USBPWR12, USBPWR34, USBPWR56)
Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU
stopped, DRAM refreshed, system running in low power mode) using the
connected USB devices. Set to +5VSB to wake up from S3 sleep mode (no
power to CPU, DRAM in slow refresh, power supply in reduced power mode).
Both jumpers are set to pins 1-2 (+5V) by default because not all computers
have the appropriate power supply to support this feature.
The USBPWR12 and USBPWR34
jumpers are for the rear USB ports.
USBPWR56 is for the internal USB connector.
•
The USB device wake-up feature requires a power supply that can provide
500mA on the +5VSB lead for each USB port. Otherwise, the system does
not power up.
•
The total current consumed must NOT exceed the power supply capability
(+5VSB) whether under normal condition or in sleep mode.
A7V400-MX
2
1
3
2
+5V
(Default)
+5VSB
(Default)
+5V
+5VSB
23
2
1
A7V400-MX USB Device Wake Up
USBPWR12
USBPWR56
USBPWR34