Asus A8V A8V-VM User's Manual for English Edition - Page 35

A8V-VM IDE Connectors

Get Asus A8V PDF manuals and user guides View all Asus A8V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

2. IDE connectors (40-1 pin PRI_IDE, SEC_IDE) These connectors are for Ultra DMA 133/100/66 signal cables. There are three interfaces on each Ultra DMA 133/100/66 signal cables: blue, black, and gray. Connect the blue interface into the motherboad's IDE connector, then select the following modes to configure your hard disk drive(s). Cable Select Mode: to select the operating mode by cable connectors. No. of drives 1 2 Drive Type Drive Jumper With OS With OS Cable select Without OS Cable Connector Black Black Gray Jumper Select Mode: to select the operating mode by hard-disk drive jumper. No. of drives 1 2 Drive Type With OS With OS Without OS Drive Jumper Master Master Slave Cable Connector Black or gray • Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable. • Use the 80-conductor IDE cable for Ultra DMA 133/100/66/33 IDE devices. NOTE: Orient the red markings on the floppy ribbon cable to PIN 1. PIN 1 PRI_IDE SEC_IDE A8V-VM R A8V-VM IDE Connectors PIN 1 ASUS A8V-VM 1-23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
1-±3
ASUS A8V-VM
•
Pin ±0 on the IDE connector is removed to match the covered hole
on the Ultra DMA cable connector. This prevents incorrect insertion
when you connect the IDE cable.
•
Use the 80-conductor IDE cable for Ultra DMA
133/100/66/33
IDE devices.
A8V-VM IDE Connectors
A8V-VM
SEC_IDE
PRI_IDE
PIN 1
PIN 1
NOTE:
Orient the red markings on
the floppy ribbon cable to PIN 1.
±.
IDE
connectors (40-1 pin PRI_IDE, SEC_IDE)
These connectors are for Ultra DMA 133/100/66 signal cables.
There are three interfaces on each Ultra DMA 133/100/66 signal
cables: blue, black, and gray. Connect the blue interface into the
motherboad’s IDE connector, then select the following modes to
configure your hard disk drive(s).
1
With OS
Master
±
With OS
Master
Black or gray
Without OS
Slave
No. of drives
Drive Type
Drive Jumper
Cable Connector
1
With OS
Black
±
With OS
Cable select
Black
Without OS
Gray
No. of drives
Drive Type
Drive Jumper
Cable Connector
Cable Select Mode: to select the operating mode by cable connectors.
Jumper Select Mode: to select the operating mode by hard-disk drive jumper.