Asus AAM6030BI User Manual - Page 14

Bridged CPE profile and Connection

Get Asus AAM6030BI PDF manuals and user guides View all Asus AAM6030BI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

AAM6030BI User Manual 4.3.1 Wide Area Network connection On the other side of the router is where your Wide Area Network (WAN) connection; also referred to as a broadband connection. This WAN connection is different for every WAN supplier. Most of the configuration you will perform will be in this area. Local Area Network Connection(s) 4.3.2 Local Area Network connection On one side of your router, you have your own Local Area network (LAN) connections. This is where you plug in your local computers to the router. The router is normally configured to automatically provide all the PC's on your network with Internet addresses. 4.4 Configuring the WAN Before the CPE will pass any data between the LAN interface(s) and the WAN interface, the WAN side of the modem must be configured. Depending upon your DSL service provider or your ISP, you will need some (or all) of the information outlined below before you can properly configure the WAN: • Your DSL line VPI and VCI • Your DSL encapsulation type and multiplexing • Your DSL training mode For PPPoA or PPPoE users, you also need these values from your ISP: • Your username and password For RFC 1483 users, you may need these values from your ISP: • Your DSL fixed Internet IP address • Your Subnet Mask • Your Default CPE • Your primary DNS IP address Since multiple users can use the CPE, the CPE can simultaneously support multiple connection types; hence, the user must set up different profiles for each connection. The CPE supports the following protocols: • DHCP • RFC 2364 PPPoA • RFC2516 PPPoE • Static • Bridged • CLIP . 4.4.1 New Connection A new connection is basically a virtual connection. Your CPE can support up to 8 different (unique) virtual connections. If you have multiple different virtual connections, you man need to utilize the static and dynamic routing capabilities of the modem to pass data correctly. 4.4.1.1 Bridged CPE profile and Connection A pure bridged connection does not assign and IP address to the WAN interface. NAT and firewall rules are not enabled. This connection method makes the router act as a hub, and just passes packets across the WAN interface to the LAN interface. To configure the CPE as a bridge, from the Home page, click on Setup and then click on New Connection. The default PPPoE connection setup is displayed. At the Type field select Bridge and the Bridge connection setup page is displayed (see Figure 4). Give your Bridge connection a unique name; the name must not have spaces and cannot begin with numbers. In this case the unique name is called bridge1. Select the encapsulation type (LLC or VC); if you are not sure just use the default mode. Select the VPI 14 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
AAM6030BI User Manual
4.3.1
Wide Area Network connection
On the other side of the router is where your Wide Area Network (WAN) connection; also referred to as a
broadband connection. This WAN connection is different for every WAN supplier. Most of the
configuration you will perform will be in this area. Local Area Network Connection(s)
4.3.2
Local Area Network connection
On one side of your router, you have your own Local Area network (LAN) connections. This is where you
plug in your local computers to the router. The router is normally configured to automatically provide all
the PC's on your network with Internet addresses.
4.4
Configuring the WAN
Before the CPE will pass any data between the LAN interface(s) and the WAN interface, the WAN side of
the modem must be configured. Depending upon your DSL service provider or your ISP, you will need
some (or all) of the information outlined below before you can properly configure the WAN:
•
Your DSL line VPI and VCI
•
Your DSL encapsulation type and multiplexing
•
Your DSL training mode
For
PPPoA
or
PPPoE
users, you also need these values from your ISP:
•
Your username and password
For
RFC 1483
users, you may need these values from your ISP:
•
Your DSL fixed Internet IP address
•
Your Subnet Mask
•
Your Default CPE
•
Your primary DNS IP address
Since multiple users can use the CPE, the CPE can simultaneously support multiple connection types;
hence, the user must set up different profiles for each connection. The CPE supports the following
protocols:
•
DHCP
•
RFC 2364 PPPoA
•
RFC2516 PPPoE
•
Static
•
Bridged
•
CLIP
.
4.4.1
New Connection
A new connection is basically a virtual connection. Your CPE can support up to 8 different (unique) virtual
connections.
If you have multiple different virtual connections, you man need to utilize the static and
dynamic routing capabilities of the modem to pass data correctly.
4.4.1.1
Bridged CPE profile and Connection
A pure bridged connection does not assign and IP address to the WAN interface.
NAT and firewall rules
are not enabled.
This connection method makes the router act as a hub, and just passes packets across the
WAN interface to the LAN interface.
To configure the CPE as a bridge, from the Home page, click on Setup and then click on New Connection.
The default PPPoE connection setup is displayed.
At the Type field select Bridge and the Bridge
connection setup page is displayed (see Figure 4).
Give your Bridge connection a unique name; the name
must not have spaces and cannot begin with numbers.
In this case the unique name is called bridge1.
Select the encapsulation type (LLC or VC); if you are not sure just use the default mode. Select the VPI
14
14