Asus AAM6030BI User Manual - Page 17

Tools, System Commands, Save All

Get Asus AAM6030BI PDF manuals and user guides View all Asus AAM6030BI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

AAM6030BI User Manual service provider is using 0,30. Also select the quality of service (QOS); leave the default value if you are unsure or the ISP did not provide this information. Following is a description of the different options: a. Username: The username for the PPPoE access; this is provided by your DSL service provider or your ISP. b. Password: The password for the PPPoE access; this is provided by your DSL service provider or your ISP. c. On-Demand: Enables on-demand mode. The connection will disconnect if no activity is detected after the specified idle timeout value. d. Idle Timeout: Specifies that PPPoE connection should disconnect if the link has no activity detected for n seconds. This field is used in conjunction with the On-Demand feature. To ensure that the link is always active, enter a 0 in this field. e. Keep Alive: When on-demand option is not enable, this value specifies the time to wait without being connected to your provider before terminating the connection. To ensure that the link is always active, enter a 0 in this field. f. Set Route: Specify this connection as the default-route. g. MRU: Maximum Receive Unit the DSL connection can receive. It is a negotiated value that asks the provider to send packets of no more than n bytes. The maximum specified value is 1500 although some DSL/ISP providers require a larger value. The minimum MRU value is 128. h. Enforce MRU: Check this box if you experience problems accessing the Internet over a PPPoE connection. This feature will force all TCP traffic to conform with PPP MRU by changing TCP Maximum Segment Size to PPP MRU. i. Debug: Enables PPPoE connection debugging facilities. Debugging is talked about later. Figure 6 (PPPOE Connection Setup) To complete the connection you must now click the apply button. The apply button will temporarily save this connection. To make the change permanent you need to click on Tools (at the top of the page) and select System Commands. At the system commands page, click on Save All. 17 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
AAM6030BI User Manual
service provider is using 0,30.
Also select the quality of service (QOS); leave the default value if you are
unsure or the ISP did not provide this information.
Following is a description of the different options:
a.
Username: The username for the PPPoE access; this is provided by your DSL service
provider or your ISP.
b.
Password: The password for the PPPoE access; this is provided by your DSL service provider
or your ISP.
c.
On-Demand: Enables on-demand mode. The connection will disconnect if no activity is
detected after the specified idle timeout value.
d.
Idle Timeout: Specifies that PPPoE connection should disconnect if the link has no activity
detected for n seconds.
This field is used in conjunction with the On-Demand feature. To
ensure that the link is always active, enter a 0 in this field.
e.
Keep Alive: When on-demand option is not enable, this value specifies the time to wait
without being connected to your provider before terminating the connection. To ensure that
the link is always active, enter a 0 in this field.
f.
Set Route: Specify this connection as the default-route.
g.
MRU: Maximum Receive Unit the DSL connection can receive. It is a negotiated value that
asks the provider to send packets of no more than n bytes. The maximum specified value is
1500 although some DSL/ISP providers require a larger value. The minimum MRU value is
128.
h.
Enforce MRU: Check this box if you experience problems accessing the Internet over a
PPPoE connection. This feature will force all TCP traffic to conform with PPP MRU by
changing TCP Maximum Segment Size to PPP MRU.
i.
Debug: Enables PPPoE connection debugging facilities.
Debugging is talked about later.
Figure 6 (PPPOE Connection Setup)
To complete the connection you must now click the apply button.
The apply button will temporarily save
this connection. To make the change permanent you need to click on
Tools
(at the top of the page) and
select
System Commands
.
At the system commands page, click on
Save All
.
17
17