Asus AAM6030BI User Manual - Page 19

Tools, System Commands, Save All, Modify an Existing Connection, Modem setup

Get Asus AAM6030BI PDF manuals and user guides View all Asus AAM6030BI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

AAM6030BI User Manual name; the name must not have spaces and cannot begin with numbers. In this case the unique name is called STATIC1. Select the encapsulation type (LLC or VC); if you are not sure just use the default mode. Select the VPI and VCI settings; your DSL service provider or your ISP will supply these; in this case the DSL service provider is using 0,35. Also select the quality of service (QOS); leave the default value if you are unsure or the ISP did not provide this information. You can also enable Network Address Translation (NAT) and the Firewall options. If you are unsure, leave these in the default mode. Based upon the information your DSL/ISP provided, enter your assigned IP address, Subnet Mask, Default CPE (if provided), and Domain Name Services (DNS) values (if provided). For the static configuration, you can also select a bridge connection or a routed connection. Since static IP address is typically used to host WEB servers, you may want to use a bridge connection. Figure 8 (Static IP Connection Setup) To complete the connection you must now click the apply button. The apply button will temporarily save this connection. To make the change permanent you need to click on Tools (at the top of the page) and select System Commands. At the system commands page, click on Save All. 4.4.2 Modify an Existing Connection To modify an existing connection, from the Home screen, click setup and then click the connection you want to modify. The connections are listed as Connection 1 through Connection 8 As a note, if you delete the connection, to make the change permanent you need to click on Tools (at the top of the page) and select System Commands. At the system commands page, click on Save All. 4.4.3 Modem setup To configure the DSL modulation type, go to the Home screen, Click setup. Under WAN Setup, select Modem Setup. This will bring up the modem setup screen. Leave the default value if you are unsure or the DSL/ISP did not provide this information. For most all cases, this screen should not be modified. The apply button will temporarily save this connection. To make the change permanent you need to click on Tools (at the top of the page) and select System Commands. At the system commands page, click on Save All. 19 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
AAM6030BI User Manual
name; the name must not have spaces and cannot begin with numbers. In this case the unique name is
called STATIC1. Select the encapsulation type (LLC or VC); if you are not sure just use the default mode.
Select the VPI and VCI settings; your DSL service provider or your ISP will supply these; in this case the
DSL service provider is using 0,35.
Also select the quality of service (QOS); leave the default value if you
are unsure or the ISP did not provide this information.
You can also enable Network Address Translation
(NAT) and the Firewall options.
If you are unsure, leave these in the default mode.
Based upon the information your DSL/ISP provided, enter your assigned IP address, Subnet Mask, Default
CPE (if provided), and Domain Name Services (DNS) values (if provided).
For the static configuration,
you can also select a bridge connection or a routed connection.
Since static IP address is typically used to
host WEB servers, you may want to use a bridge connection.
Figure 8 (Static IP Connection Setup)
To complete the connection you must now click the apply button.
The apply button will temporarily save
this connection. To make the change permanent you need to click on
Tools
(at the top of the page) and
select
System Commands
.
At the system commands page, click on
Save All
.
4.4.2
Modify an Existing Connection
To modify an existing connection, from the Home screen, click setup and then click the connection you
want to modify.
The connections are listed as Connection 1 through Connection 8
As a note, if you delete the connection, to make the change permanent you need to click on
Tools
(at the
top of the page) and select
System Commands
. At the system commands page, click on
Save All
.
4.4.3
Modem setup
To configure the DSL modulation type, go to the Home screen, Click setup. Under WAN Setup, select
Modem Setup. This will bring up the modem setup screen.
Leave the default value if you are unsure or the
DSL/ISP did not provide this information.
For most all cases, this screen should not be modified.
The apply button will temporarily save this connection. To make the change permanent you need to click
on
Tools
(at the top of the page) and select
System Commands
. At the system commands page, click on
Save All
.
19
19