Asus AT4NM10T-I User Manual - Page 21

Asus AT4NM10T-I Manual

Get Asus AT4NM10T-I PDF manuals and user guides View all Asus AT4NM10T-I manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

2. These connectors connect to Serial ATA 3.0 Gb/s hard disk drives and optical drives via Serial ATA 3.0 Gb/s signal cables. Serial ATA connectors (7-pin SATA_1, SATA_2, SATA_E1, SATA_E2) SATA3G_E2 SATA3G_2 GND RSATA_TXP2 RSATA_TXN2 GND RSATA_RXP2 RSATA_RXN2 GND SATA3G_E1 GND RSATA_RXN1 RSATA_RXP1 GND RSATA_TXN1 RSATA_TXP1 GND AT4NM10T-I SATA3G_1 GND RSATA_RXN1 RSATA_RXP1 GND RSATA_TXN1 RSATA_TXP1 GND AT4NM10T-I SATA 3.0Gb/s connectors • Install the Windows® XP Service Pack 3 or later version before using Serial ATA. • The SATA3G_E1/E2 (black) connectors are for data drives only. ATAPI device is not supported. 3. These connectors are for USB 2.0 ports. Connect the USB module cable to this connector, then install the module to a slot opening at the back of the system chassis. This USB connector complys with USB 2.0 specification that supports up to 480 Mbps connection speed. USB connectors (10-1 pin USB78) AT4NM10T-I USB78 PIN 1 AT4NM10T-I USB2.0 connector Never connect a 1394 cable to the USB connector. Doing so will damage the motherboard! The USB module cable is purchased separately. 1-11 USB+5V USB_P7USB_P7+ GND USB+5V USB_P8USB_P8+ GND NC GND RSATA_TXP2 RSATA_TXN2 GND RSATA_RXP2 RSATA_RXN2 GND Chapter 1: Product introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
1-11
Chapter 1: Product introduction
2.
Serial ATA connectors (7-pin SATA_1, SATA_2, SATA_E1, SATA_E2)
These connectors connect to Serial ATA 3.0 Gb/s hard disk drives and optical drives via
Serial ATA 3.0 Gb/s signal cables.
GND
RSATA_RXN1
RSATA_RXP1
GND
RSATA_TXN1
RSATA_TXP1
GND
SATA3G_E2
SATA3G_E1
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
GND
RSATA_RXN1
RSATA_RXP1
GND
RSATA_TXN1
RSATA_TXP1
GND
SATA3G_2
SATA3G_1
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
AT4NM10T-I
• Install the Windows
®
XP Service Pack 3 or later version before using Serial ATA.
•
The SATA3G_E1/E2 (black) connectors are for data drives only. ATAPI device is not
supported.
3.
USB connectors (10-1 pin USB78)
These connectors are for USB 2.0 ports. Connect the USB module cable to this
connector, then install the module to a slot opening at the back of the system chassis.
This USB connector complys with USB 2.0 speciFcation that supports up to 480 Mbps
connection speed.
AT4NM10T-I
AT4NM10T-I USB2.0 connector
PIN 1
USB+5V
USB_P8-
USB_P8+
GND
NC
USB+5V
USB_P7-
USB_P7+
GND
USB78
Never connect a 1394 cable to the USB connector. Doing so will damage the motherboard!
The USB module cable is purchased separately.