Asus DSL-N12HP users manual in English - Page 132

Appendix E - Connection Setup, E1 Layer 2 Interfaces, E1.1 ATM Interfaces

Get Asus DSL-N12HP PDF manuals and user guides View all Asus DSL-N12HP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 132 highlights

Appendix E - Connection Setup Creating a WAN connection is a two-stage process. 1 - Setup a Layer 2 Interface (ATM or Ethernet WAN). 2 - Add a WAN connection to the Layer 2 Interface. You can reach this page by clicking on the Basic Setup icon located on the left side of the screen. The following sections describe each stage in turn. E1 Layer 2 Interfaces Every layer2 interface operates in Multi-Service Connection (VLAN MUX) mode, which supports multiple connections over a single interface. Note that PPPoA and IPoA connection types are not supported for Ethernet WAN interfaces. After adding WAN connections to an interface, you must also create an Interface Group to connect LAN/WAN interfaces. E1.1 ATM Interfaces Follow these procedures to configure an ATM interface. NOTE: The DSL-N12HP supports up to 16 ATM interfaces. 132

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
132
Appendix E - Connection Setup
Creating a WAN connection is a two-stage process.
1 - Setup a Layer 2 Interface (ATM or Ethernet WAN).
2 - Add a WAN connection to the Layer 2 Interface.
You can reach this page by clicking on the Basic Setup icon
located on the left side of the screen.
The following sections describe each stage in turn.
E1
Layer 2 Interfaces
Every layer2 interface operates in Multi-Service Connection
(VLAN MUX) mode, which supports multiple connections over a
single interface. Note that PPPoA and IPoA connection types are
not supported for Ethernet WAN interfaces. After adding WAN
connections to an interface, you must also create an Interface
Group to connect LAN/WAN interfaces.
E1.1 ATM Interfaces
Follow these procedures to configure an ATM interface.
NOTE
: The DSL-N12HP supports up to 16 ATM interfaces.