Asus P I-P55T2P4 User Manual - Page 29

Turbo LED Lead CON1, SMI Suspend Switch Lead CON1, Reset Switch Lead CON1, Keyboard Lock Switch Lead

Get Asus P I-P55T2P4 PDF manuals and user guides View all Asus P I-P55T2P4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

III. INSTALLATION (Connectors) III. INSTALLATION 9. Turbo LED Lead (CON1) The motherboard's turbo function is always on. The turbo LED connection is labeled here but the LED will remain constantly lit while the system power is on. You may wish to connect the Power LED from the system case to this lead. See the figure below. 10. SMI Suspend Switch Lead (CON1) This allows the user to manually place the system into a suspend mode or "Green" mode where system activity will be instantly decreased to save electricity and expand the life of certain components when the system is not in use. This 2-pin connector (see the figure below) connects to the case-mounted suspend switch. If you do not have a switch for the connector, you may use the "Turbo Switch" since it does not have a function. SMI is activated when it detects a short to open moment and therefore leaving it shorted will not cause any problems. May require one or two pushes depending on the position of the switch. Wake-up can be controlled by settings in the BIOS but the keyboard will always allow wakeup (the SMI lead cannot wake-up the system). If you want to use this connector, "Suspend Switch" in the POWER MANAGEMENT SETUP of the BIOS software should be on the default setting of Enable. 11. Reset Switch Lead (CON1) This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch This is a preferred method of rebooting in order to prolong the life of the system's power supply. See the figure below. 12. Keyboard Lock Switch Lead & System Power LED (CON1) This 5-pin connector connects to the case-mounted keyboard lock switch for locking the keyboard and also to connect the system power LED. The system power LED lights when the system is powered on. See the figure below. 13. Speaker Connector (CON1) This 4-pin connector connects to the case-mounted speaker. Turbo or Power LED +5V GND SMI Lead GND Reset SW GND +5V NC Power LED & GND LOCK Keyboard Lock GND +5V GND Speaker GND Connector SPKR System Case Connections ASUS P/I-P55T2P4 User's Manual 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
ASUS P/I-P55T2P4 User's Manual
23
III. INSTALLATION
(Connectors)
III.
INSTALLATION
9.
Turbo LED Lead (CON1)
The motherboard's turbo function is always on.
The turbo LED connection is
labeled here but the LED will remain constantly lit while the system power is
on.
You may wish to connect the Power LED from the system case to this lead.
See the figure below.
10. SMI Suspend Switch Lead (CON1)
This allows the user to manually place the system into a suspend mode or "Green"
mode where system activity will be instantly decreased to save electricity and
expand the life of certain components when the system is not in use.
This 2-pin
connector (see the figure below) connects to the case-mounted suspend switch.
If you do not have a switch for the connector, you may use the "Turbo Switch"
since it does not have a function.
SMI is activated when it detects a
short to open
moment and therefore leaving it shorted will not cause any problems.
May re-
quire one or two pushes depending on the position of the switch.
Wake-up can
be controlled by settings in the BIOS but the keyboard will always allow wake-
up (the SMI lead cannot wake-up the system).
If you want to use this connector,
"Suspend Switch" in the POWER MANAGEMENT SETUP of the BIOS soft-
ware should be on the default setting of
Enable.
11.
Reset Switch Lead (CON1)
This 2-pin connector connects to the case-mounted reset switch for rebooting
your computer without having to turn off your power switch
This is a pre-
ferred method of rebooting in order to prolong the life of the system's power
supply.
See the figure below.
12. Keyboard Lock Switch Lead & System Power LED (CON1)
This 5-pin connector connects to the case-mounted keyboard lock switch for
locking the keyboard and also to connect the system power LED.
The system
power LED lights when the system is powered on.
See the figure below.
13.
Speaker Connector (CON1)
This 4-pin connector connects to the case-mounted speaker.
System Case Connections
+5V
NC
GND
LOCK
GND
+5V
SPKR
Keyboard Lock
Speaker
Connector
Power LED &
GND
GND
+5V
GND
Reset SW
SMI Lead
Turbo or
Power LED
GND
GND