Asus P I-P55T2P4 User Manual - Page 30

CPU Cooling Fan Connector FAN, WARNING, These are not, jumpers, do not place jumper caps over these

Get Asus P I-P55T2P4 PDF manuals and user guides View all Asus P I-P55T2P4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

III. INSTALLATION 14. CPU Cooling Fan Connector (FAN) This connector supports a CPU cooling fan of 500mAMP (6WATT) or less. Orientate the fan so that the heat sink fins allow airflow to go across the onboard heat sink(s) instead of the expansion slots. Depending on the fan manufacturer, the wiring and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan's plug to the board taking into consideration the polarity of the this connector. WARNING: The CPU and/or motherboard will overheat if there is no airflow across the CPU and onboard heatsinks. Damage may occur to the motherboard and/or the CPU fan if these pins are incorrectly used. These are not jumpers, do not place jumper caps over these pins. III. INSTALLATION (Connectors) Air Flow FAN GND +12V CPU Fan Power Air Flow 15. IrDA-Compliant Infrared Module Connector (IR) This connector supports the optional wireless transmitting and receiving infrared module. This module mounts to a small opening on system cases that support this feature. You must also configure the setting through BIOS setup on page 36 "UART2 Use Infrared" to select whether UART2 is directed for use with COM2 or IrDA. Use the five pins as shown on the Back View and connect a ribbon cable from the module to the motherboard according to the pin definitions. Front View Back View +5V IRRX IRTX NC GND Infrared Module Connector IRTX +5V GND NC IRRX 24 ASUS P/I-P55T2P4 User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
ASUS P/I-P55T2P4 User's Manual
24
III. INSTALLATION
(Connectors)
III.
INSTALLATION
14. CPU Cooling Fan Connector (FAN)
This connector supports a CPU cooling fan of 500mAMP (6WATT) or less.
Orientate the fan so that the heat sink fins allow airflow to go across the on-
board heat sink(s) instead of the expansion slots.
Depending on the fan manu-
facturer, the wiring and plug may be different.
The red wire should be posi-
tive, while the black should be ground.
Connect the fan's plug to the board
taking into consideration the polarity of the this connector.
WARNING:
The CPU and/or motherboard will overheat if there is no airflow
across the CPU and onboard heatsinks.
Damage may occur to the mother-
board and/or the CPU fan if these pins are incorrectly used.
These are not
jumpers, do not place jumper caps over these pins.
Air Flow
Air Flow
CPU Fan Power
FAN
+12V
GND
15. IrDA-Compliant Infrared Module Connector (IR)
This connector supports the optional wireless transmitting and
receiving infrared module.
This module mounts to a small opening on system
cases that support this feature.
You must also configure the setting through
BIOS setup on page 36 "UART2 Use Infrared" to select whether UART2 is
directed for use with COM2 or IrDA.
Use the five pins as shown on the Back
View and connect a ribbon cable from the module to the motherboard accord-
ing to the pin definitions.
Infrared Module Connector
Front View
+5V
IRTX
IRRX
NC
GND
Back View
IRRX
+5V
IRTX
NC
GND