Asus P2L97 P2L97 User Manual - Page 28

Universal Serial BUS Ports 1 & 2 Two 4-pin Female

Get Asus P2L97 PDF manuals and user guides View all Asus P2L97 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

R III. INSTALLATION (Connectors) III. INSTALLATION 6. Universal Serial BUS Ports 1 & 2 (Two 4-pin Female) Two USB ports are available for connecting USB devices. USB 1 Universal Serial Bus (USB) 2 7. Primary / Secondary IDE connectors (Two 40-1pin IDE) These connectors support the provided IDE hard disk ribbon cable. After connecting the single end to the board, connect the two plugs at the other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumper accordingly. Please refer to the documentation of your hard disk for the jumper settings. BIOS now supports SCSI device or IDE CD-ROM bootup (see "HDD Sequence SCSI/IDE First" & "Boot Sequence" in the BIOS Features Setup of the BIOS SOFTWARE) (Pin 20 is removed to prevent inserting in the wrong orientation when using ribbon cables with pin 20 plugged). TIP: You may configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector. You may install one operating system on an IDE drive and another on a SCSI drive and select the boot disk through BIOS Features Setup. NOTE: Orient the red stripe to Pin 1 Pin 1 Secondary IDE Connector P2L97 IDE Connectors Primary IDE Connector 28 ASUS P2L97 User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
28
ASUS P2L97 User’s Manual
(Connectors)
III.
INSTALLATION
III. INSTALLATION
6.
Universal Serial BUS Ports 1 & 2 (Two 4-pin Female)
Two USB ports are available for connecting USB devices.
Universal Serial Bus (USB) 2
USB 1
7.
Primary / Secondary IDE connectors (Two 40-1pin IDE)
These connectors support the provided IDE hard disk ribbon cable. After con-
necting the single end to the board, connect the two plugs at the other end to
your hard disk(s). If you install two hard disks, you must configure the second
drive to Slave mode by setting its jumper accordingly. Please refer to the docu-
mentation of your hard disk for the jumper settings. BIOS now supports SCSI
device or IDE CD-ROM bootup (see “HDD Sequence SCSI/IDE First” & “Boot
Sequence” in the
BIOS Features Setup
of the BIOS SOFTWARE)
(Pin 20 is
removed to prevent inserting in the wrong orientation when using ribbon
cables with pin 20 plugged).
TIP:
You may configure two hard disks to be both Masters using one ribbon
cable on the primary IDE connector and another ribbon cable on the secondary
IDE connector. You may install one operating system on an IDE drive and an-
other on a SCSI drive and select the boot disk through BIOS Features Setup.
Primary IDE Connector
Pin 1
Secondary IDE Connector
P2L97 IDE Connectors
NOTE:
Orient the red stripe to Pin 1