Asus P4BP-MX P4BP-MX User Manual - Page 28

CPU and chassis fan connectors 3-pin CPUFAN2, CHASFAN1, USB header 10-1 pin USB1 - motherboard driver

Get Asus P4BP-MX PDF manuals and user guides View all Asus P4BP-MX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

5. CPU and chassis fan connectors (3-pin CPUFAN2, CHASFAN1) The fan connectors support cooling fans of 350mA~740mA (8.88W max.) or a total of 1A~2.22A (26.64W max.) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. CPUFAN1 GND +12V Rotation P4BP-MX CHASFAN1 Rotation +12V GND P4BP-MX 12-Volt Cooling Fan Power Do not forget to connect the fan cables to the fan connectors. Lack of sufficient air flow within the system may damage the motherboard components. These are not jumpers! DO NOT place jumper caps on the fan connectors! 6. USB header (10-1 pin USB1) If the USB ports on the rear panel are inadequate, a USB header is available for additional USB ports. Connect the USB cable of the USB 2.0 module to this header. You may install the USB module in the chassis front panel. The module has two USB 2.0 ports for connecting next generation USB peripherals such as high resolution cameras, scanners, and printers. USB+5V LDM5 LDP5 GND NC P4BP-MX P4BP-MX USB 2.0 Header USB1 1 USB+5V LDM6 LDP6 GND • The USB 2.0 module is purchased separately. • Install the USB 2.0 driver before using the USB 2.0 feature. 1-18 Chapter 1: Product introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
1-18
Chapter 1: Product introduction
5.
CPU and chassis fan connectors (3-pin CPUFAN2, CHASFAN1)
The fan connectors support cooling fans of 350mA~740mA (8.88W max.) or a
total of 1A~2.22A (26.64W max.) at +12V. Connect the fan cables to the fan
connectors on the motherboard, making sure that the black wire of each cable
matches the ground pin of the connector.
Do not forget to connect the fan cables to the fan connectors. Lack of sufficient
air flow within the system may damage the motherboard components. These
are not jumpers! DO NOT place jumper caps on the fan connectors!
6.
USB header (10-1 pin USB1)
If the USB ports on the rear panel are inadequate, a USB header is available
for additional USB ports. Connect the USB cable of the USB 2.0 module to this
header. You may install the USB module in the chassis front panel. The
module has two USB 2.0 ports for connecting next generation USB peripherals
such as high resolution cameras, scanners, and printers.
•
The USB 2.0 module is purchased separately.
•
Install the USB 2.0 driver before using the USB 2.0 feature.
P4BP-MX
P4BP-MX
12-Volt Cooling Fan Power
CPUFAN1
CHASFAN1
GND
Rotation
+12V
GND
Rotation
+12V
P4BP-MX
P4BP-MX USB 2.0 Header
USB+5V
LDM5
LDP5
GND
NC
USB+5V
LDM6
LDP6
GND
1
USB1