Home » Asus Manuals » Motherboards » Asus P8H67-M2 SI » Manual Viewer

Asus P8H67-M2 SI User Manual - Page 21

P8H67-M2/TPM/SI Chassis intrusion connector

Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

2. CPU and chassis fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN) Connect the fan cables to the fan connectors on the motherboard, ensuring that the black wire of each cable matches the ground pin of the connector. CPU_FAN CPU FAN PWM CPU FAN IN CPU FAN PWR GND P8H67-M2/TPM/SI CHA_FAN GND +12V Rotation P8H67-M2/TPM/SI Fan connectors Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! Do not place jumper caps on the fan connectors! 3. Chassis intrusion connector (4-1 pin CHASSIS) This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced. The signal is then generated as a chassis intrusion event. By default, the pin labeled "Chassis Signal" and "Ground" are shorted with a jumper cap. Remove the jumper caps only when you intend to use the chassis intrusion detection feature. CHASSIS P8H67-M2/TPM/SI P8H67-M2/TPM/SI Chassis intrusion connector +5VSB_MB Chassis Signal GND Chapter 1: Product introduction 1-11

Section	Page
Notices	6
Safety information	7
About this guide	8
P8H67-M2 Series specifications summary	9
Chapter 1	11
Product introduction	11
1.1 Before you proceed	11
1.2 Motherboard overview	12
1.2.1 Motherboard layout	12
1.2.2 Layout contents	13
1.3 Central Processing Unit (CPU)	13
1.4 System memory	14
1.4.1 Overview	14
1.4.2 Memory configurations	15
1.5 Expansion slots	17
1.5.1 Installing an expansion card	17
1.5.2 Configuring an expansion card	17
1.5.3 PCI slot	17
1.5.4 PCI Express x1 slot	17
1.5.5 PCI Express x16 slot	17
1.6 Jumpers	18
1.7 Connectors	19
1.7.1 Rear panel connectors	19
1.7.2 Internal connectors	20
1.8 Software support	27
1.8.1 Installing an operating system	27
1.8.2 Support DVD information	27
Chapter 2	29
BIOS information	29
2.1 Managing and updating your BIOS	29
2.1.1 ASUS Update utility	29
2.1.2 ASUS EZ Flash 2	30
2.1.3 ASUS CrashFree BIOS 3 utility	31
2.1.4 ASUS BIOS Updater	32
2.2 BIOS setup program	35
2.3 Main menu	38
2.3.1 System Language [English]	39
2.3.2 System Date [Day xx/xx/xxxx]	39
2.3.3 System Time [xx:xx:xx]	39
2.3.4 Security	39
2.4 Ai Tweaker menu	40
2.4.1 Memory Frequency [Auto]	41
2.4.2 iGPU Max. Frequency [Auto]	41
2.4.3 GPU Boost [OK]	41
2.4.4 DRAM Timing Control	41
2.4.5 CPU Power Management	41
2.5 Advanced menu	42
2.5.1 CPU Configuration	43
2.5.2 System Agent Configuration	44
2.5.3 PCH Configuration	44
2.5.4 SATA Configuration	44
2.5.5 USB Configuration	45
2.5.6 Onboard Devices Configuration	45
2.5.7 APM	47
2.6 Monitor menu	48
2.6.1 CPU Temperature / MB Temperature [xxxºC/xxxºF]	49
2.6.2 CPU / Chassis Fan Speed [xxxx RPM] or [Ignore] / [N/A]	49
2.6.3 CPU Q-Fan Control [Enabled]	49
2.6.4 Chassis Q-Fan Control [Enabled]	50
2.6.5 CPU Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage	50
2.6.6 Anti Surge Support [Enabled]	50
2.7 Boot menu	51
2.7.1 Bootup NumLock State [On]	51
2.7.2 Full Screen Logo [Enabled]	51
2.7.3 Wait for ‘F1’ If Error [Enabled]	51
2.7.4 Option ROM Messages [Force BIOS]	52
2.7.5 Setup Mode [EZ Mode]	52
2.7.6 Boot Option Priorities	52
2.7.7 Boot Override	52
2.8 Tools menu	53
2.8.1 ASUS EZ Flash Utility	53
2.8.2 ASUS SPD Information	53
2.8.3 ASUS O.C. Profile	53

Match case Limit results 1 per page

1-11

Chapter 1: Product introduction

Do not forget to connect the fan cables to the fan connectors. Insufﬁcient air ﬂow inside the

system may damage the motherboard components. These are not jumpers! Do not place

jumper caps on the fan connectors!

CPU and chassis fan connectors (4-pin CPU_FAN, 3-pin CHA_FAN)

Connect the fan cables to the fan connectors on the motherboard, ensuring that the

black wire of each cable matches the ground pin of the connector.

Chassis intrusion connector (4-1 pin CHASSIS)

This connector is for a chassis-mounted intrusion detection sensor or switch. Connect

one end of the chassis intrusion sensor or switch cable to this connector. The chassis

intrusion sensor or switch sends a high-level signal to this connector when a chassis

component is removed or replaced. The signal is then generated as a chassis intrusion

event.

By default, the pin labeled “Chassis Signal” and “Ground” are shorted with a jumper

cap. Remove the jumper caps only when you intend to use the chassis intrusion

detection feature.

CPU_FAN

CPU FAN PWM

CPU FAN IN

CPU FAN PWR

GND

+12V

Rotation

P8H67-M2/TPM/SI

P8H67-M2/TPM/SI Fan connectors

CHA_FAN

P8H67-M2/TPM/SI

P8H67-M2/TPM/SI Chassis intrusion connector

+5VSB_MB

Chassis Signal

GND

CHASSIS