Asus TX97-X User Manual - Page 31

Keyboard Lock Switch Lead & System Power LED PANEL

Get Asus TX97-X PDF manuals and user guides View all Asus TX97-X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

III. INSTALLATION (Connectors) III. INSTALLATION 13. Message LED Lead (PANEL) This indicates whether a message has been received from a fax/modem. The LED will remain lit when there is no signal and blink when there is data transfer or waiting in the inbox). 14. SMI Suspend Switch Lead (PANEL) This allows the user to manually place the system into a suspend mode or "Green" mode where system activity will be instantly decreased to save electricity and expand the life of certain components when the system is not in use. This 2-pin connector (see the figure below) connects to the case-mounted suspend switch. If you do not have a switch for the connector, you may use the "Turbo Switch" since it does not have a function. SMI is activated when it detects a short to open moment and therefore leaving it shorted will not cause any problems. May require one or two pushes depending on the position of the switch. Wake-up can be controlled by settings in the BIOS but the keyboard will always allow wakeup (the SMI lead cannot wake-up the system). If you want to use this connector, "Suspend Switch" in the Power Management Setup of the BIOS SOFTWARE section should be on the default setting of Enable. 15. ATX Power Switch / Soft Power Switch (PANEL) The system power is controlled by a momentary switch connected to this lead. Pushing the button once will switch the system between ON and SLEEP. Pushing the switch while in the ON mode for more than 4 seconds will turn the system off. The system power LED shows the status of the system's power. 16. Reset Switch Lead (PANEL) This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch This is a preferred method of rebooting in order to prolong the life of the system's power supply. 17. Keyboard Lock Switch Lead & System Power LED (PANEL) This 5-pin connector connects to the case-mounted keyboard lock switch for locking the keyboard and also to connect the system power LED. The system power LED lights when the system is powered on and blinks in sleep mode. 18. Speaker Connector (PANEL) This 4-pin connector connects to the case-mounted speaker. R System Panel Connections Message LED +5V GND SMI Lead GND ATX Power Switch GND Reset SW GND +5V System NC GND Power LED LOCK GND Keyboard Lock +5V GND Speaker GND Connector SPKR ASUS TX97-X User's Manual 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
ASUS TX97-X User’s Manual
31
III. INSTALLATION
13. Message LED Lead (PANEL)
This indicates whether a message has been received from a fax/modem.
The
LED will remain lit when there is no signal and blink when there is data transfer
or waiting in the inbox).
14. SMI Suspend Switch Lead (PANEL)
This allows the user to manually place the system into a suspend mode or "Green"
mode where system activity will be instantly decreased to save electricity and
expand the life of certain components when the system is not in use.
This 2-pin
connector (see the figure below) connects to the case-mounted suspend switch.
If you do not have a switch for the connector, you may use the "Turbo Switch"
since it does not have a function.
SMI is activated when it detects a
short to
open
moment and therefore leaving it shorted will not cause any problems.
May
require one or two pushes depending on the position of the switch.
Wake-up can
be controlled by settings in the BIOS but the keyboard will always allow wake-
up (the SMI lead cannot wake-up the system).
If you want to use this connector,
"Suspend Switch" in the
Power Management Setup
of the BIOS SOFTWARE
section should be on the default setting of
Enable.
15. ATX Power Switch / Soft Power Switch (PANEL)
The system power is controlled by a momentary switch connected to this lead.
Pushing the button once will switch the system between ON and SLEEP.
Push-
ing the switch while in the ON mode for more than 4 seconds will turn the
system off.
The system power LED shows the status of the system's power.
16. Reset Switch Lead (PANEL)
This 2-pin connector connects to the case-mounted reset switch for rebooting
your computer without having to turn off your power switch
This is a preferred
method of rebooting in order to prolong the life of the system's power supply.
17. Keyboard Lock Switch Lead & System Power LED (PANEL)
This 5-pin connector connects to the case-mounted keyboard lock switch for
locking the keyboard and also to connect the system power LED.
The system
power LED lights when the system is powered on and blinks in sleep mode.
18. Speaker Connector (PANEL)
This 4-pin connector connects to the case-mounted speaker.
System Panel Connections
+5V
NC
GND
LOCK
GND
+5V
SPKR
Speaker
Connector
GND
GND
GND
+5V
Reset SW
SMI Lead
Message
LED
ATX Power
Switch
System
Power LED
Keyboard Lock
GND
GND
GND
(Connectors)
III.
INSTALLATION