Asus p4r800vm P4R800-VM User Manual - Page 28

Internal connectors

Get Asus p4r800vm PDF manuals and user guides View all Asus p4r800vm manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

1.10.2 Internal connectors 1. IDE connectors (40-1 pin PRI_IDE1, SEC_IDE1) This connector supports the provided UltraATA100 IDE hard disk ribbon cable. Connect the cable's blue connector to the primary (recommended) or secondary IDE connector, then connect the gray connector to the UltraATA100 slave device (hard disk drive) and the black connector to the UltraATA100 master device. 1. Follow the hard disk drive documentation when setting the device in master or slave mode. 2. Pin 20 on each IDE connector is removed to match the covered hole on the UltraATA cable connector. This prevents incorrect orientation when you connect the cables. 3. The hole near the blue connector on the UltraATA cable is intentional. P4R800-VM P4R800-VM IDE Connectors SEC_IDE1 PIN 1 PRI_IDE1 NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. 2. Floppy disk drive connector (34-1 pin FLOPPY1) This connector supports the provided floppy drive ribbon cable. After connecting one end to the motherboard, connect the other end to the floppy drive. (Pin 5 is removed to prevent incorrect insertion when using ribbon cables with pin 5 plug). FLOPPY1 P4R800-VM NOTE: Orient the red markings on the floppy ribbon cable to PIN 1. PIN 1 P4R800-VM Floppy Disk Drive Connector 1-18 Chapter 1: Product introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
1-18
Chapter 1: Product introduction
1.10.2
Internal connectors
1.
IDE connectors (40-1 pin PRI_IDE1, SEC_IDE1)
This connector supports the provided UltraATA100 IDE hard disk ribbon cable.
Connect the cable
’
s blue connector to the primary (recommended) or secondary
IDE connector, then connect the gray connector to the UltraATA100 slave device
(hard disk drive) and the black connector to the UltraATA100 master device.
P4R800-VM
P4R800-VM IDE Connectors
NOTE:
Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
SEC_IDE1
PRI_IDE1
PIN 1
2.
Floppy disk drive connector (34-1 pin FLOPPY1)
This connector supports the provided floppy drive ribbon cable. After
connecting one end to the motherboard, connect the other end to the floppy
drive. (Pin 5 is removed to prevent incorrect insertion when using ribbon cables
with pin 5 plug).
P4R800-VM
NOTE:
Orient the red markings on
the floppy ribbon cable to PIN 1.
P4R800-VM Floppy Disk Drive Connector
PIN 1
FLOPPY1
1.
Follow the hard disk drive documentation when setting the device in master
or slave mode.
2.
Pin 20 on each IDE connector is removed to match the covered hole on the
UltraATA cable connector. This prevents incorrect orientation when you
connect the cables.
3.
The hole near the blue connector on the UltraATA cable is intentional.