Behringer FLOW 8 Quick Start Guide - Page 19

36 FLOW 8 MIDI Implementation OVERVIEW Input Channels MIDI Section Ch. Input Ch. 1 1 Input Ch. 2 2 Input Ch. 3 3 Input Ch. 4 4 Input Ch. 5/6 5 Input Ch. 7/8 6 Input Ch. USB/BT 7 Busses MIDI Section Ch. MAIN BUS 8 MON1 BUS 9 MON2 BUS 10 FX 1 BUS 11 FX 2 BUS 12 FX-Slots MIDI Section Ch. FX 1 14 FX 2 15 MIDI Global Control Section Ch. SNAPSHOTS - whole mixer 16 FX 1 / FX 2 - common ctrl. " [MIDI-Ch. 13 = not used] INPUT CHANNELS Section Input Ch. 1 " " " " " " " " MIDI Ch. Command Min. Value Max. Value Parameter Min. Value Max. Value Notes Comment 1 CC 7 0, 1 127 Channel LEVEL (to MAIN) OFF, -70 dB +10 dB Value 0 = OFF, Value 1~127 = the actual level control from -70 to +10 dB " CC 10 0 127 Channel BALANCE (to MAIN) 1.0 LEFT 1.0 RIGHT Value 64 = "0.0 CENTER" " CC 5 0 1-127 MUTE NO MUTE MUTE Switch; value 0 = "MUTE OFF"; value 1-127 = "MUTE" " CC 6 0 1-127 SOLO NO SOLO SOLO Switch; value 0 = "SOLO OFF"; value 1-127 = "SOLO" " CC 1 0 127 EQ LOW -15 dB +15 dB Continuous control; value 64 = "0.0 dB" (center postion) " CC 2 " " EQ LOW MID " " " " CC 3 " " EQ HI MID " " " " CC 4 " " EQ HI " " " " CC 8 0 127 GAIN -20 dB +60 dB NOT on Ch. USB/BT Continuous control " CC 9 0 127 LOW CUT 20 Hz 600 Hz NOT on Ch. USB/BT Continuous control " CC 11 0 100-127 COMP Continuous control; values 0% 100% NOT on Ch. USB/BT 101-127 = identical to max. value = 100% " CC 12 0 1-127 48 V Switch; value 0 = "48V OFF ON ONLY on Ch. 1 + 2 OFF"; value 1-127 = "48V ON" " CC 14 0, 1 127 SEND LEVEL to MON1 OFF, -70 dB +10 dB Value 0 = OFF, Value 1~127 = the actual level control from -70 to +10 dB " CC 15 0, 1 127 SEND LEVEL to MON2 OFF, -70 dB +10 dB " " CC 16 0, 1 127 SEND LEVEL to FX 1 OFF, -70 dB +10 dB " " CC 17 0, 1 127 SEND LEVEL to FX 2 OFF, -70 dB +10 dB " >Each Input Channel is assigned to one specific MIDI-Channel. Quick Start Guide 37 BUSSES Section MAIN BUS " " " MIDI Ch. Command Min. Value 8 CC 7 0, 1 " CC 10 0 " CC 8 0 " CC 11 0 " CC 12 " " CC 13 " " CC 14 " " CC 15 " " CC 16 " " CC 17 " " CC 18 " " CC 19 " Max. Value Parameter Min. Value Max. Value 127 BUS LEVEL OFF, -70 dB +10 dB 127 BUS BALANCE 1.0 LEFT 1.0 RIGHT 127 BUS LIMITER -30 dB 0 dB 127 9-BAND EQ 62 Hz -15 dB +15 dB " 9-BAND EQ 125 Hz " " " 9-BAND EQ 250 Hz " " " 9-BAND EQ 500 Hz " " " 9-BAND EQ 1 kHz " " " 9-BAND EQ 2 kHz " " " 9-BAND EQ 4 kHz " " " 9-BAND EQ 8 kHz " " " 9-BAND EQ 16 kHz " " Notes Comment Value 0 = OFF, Value 1~127 = the actual level control from -70 to +10 dB ONLY on MAIN BUS Value 64 = "0.0 CENTER" NOT on FX 1/2 BUS Continuous control Continuous control; value NOT on FX 1/2 BUS 64 = "0.0 dB" (center postion) " " " " " " " " " " " " " " " " >Each BUS is assigned to one specific MIDI-Channel. FX CONTROL Section MIDI Ch. Command Min. Value Max. Value Parameter Min. Value Max. Value FX 1 / FX 2 14 / 15 Prog. Chg. 1 16 EFFECT PRESET 1 16 " " CC 1 0 100-127 PARAMETER 1 0% 100% " " CC 2 0 1-127 PARAMETER 2 Value A >Each FX slot is assigned to one specific MIDI-Channel. GLOBAL CONTROL Value B Notes Comment Program Change 0 & 17-127 = ignored Continuous control; values 101-127 = identical to max. value = 100% Switch; MIDI value 0 = "Value A"; MIDI value 1-127 = "Value B" Section SNAPSHOT FX 1 / FX 2 FX 1 / FX 2 MIDI Ch. Command Min. Value Max. Value 16 Prog. Chg. 1 16 " CC 1 0 1-127 " Note 0 (C -1) Velocity 1 Velo. 127 Parameter Load MIXER SNAPSHOT FX MUTE TAP TEMPO Min. Value Max. Value Notes Comment 1 NO MUTE 50 BPM 16 MUTE 250 BPM Program Change 0 & 17-127 Loading #16 = RESET! = ignored; Presets = 1-15; RESET = Prog. Chg. #16 Mutes BOTH FX Sends Switch; value 0 = "MUTE OFF"; value 1-127 = "MUTE" See below! Lowest MIDI note for tempo tapping; ignore Velocity 0, any velo. btw. 1-127 = OK > ALL global controls operate on MIDI-Channel 16. Notes to TAP TEMPO: 1.) Note On command will be used to control the FX tempo; Note Off will be ignored. 2.) Any Note Velocity from 1-127 is OK for triggering, Velocity 0 will be ignored. 3.) Tempo calculation will be done by measuring the time interval between repetitive hit of MIDI-Note 0 (same logic as for the hardware TAP button on the mixer). 4.) TAP TEMPO affects generally both FX slots, so it's a "global tempo". 5.) TAP TEMPO is only useable for delay/echo effects which offer this parameter ( FX 2 > Presets No. 1-12).