Beko HII64500FHT User Manual - Page 10

Danger

Get Beko HII64500FHT PDF manuals and user guides View all Beko HII64500FHT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Our company shall not be liable for any damages that will arise due to using the product without a grounding Ainstallation in accordance with the local regulations. a DANGER: I The product must be connected to the mains . supply only by an authorised and qualified person. The product's warranty period starts only after correct installation. Manufacturer shall not be held responsible for damages arising from procedures carried out by unauthorised persons. "" DANGER: • The power cable must not be clamped, bent or trapped or come into contact with hot parts of the product. A damaged power cable must be replaced by a qualified electrician. Otherwise, there is risk of electric shock, short circuit or fire! • Connection must comply with national regulations. • The mains supply data must correspond to the data specified on the type label of the product. Type label is at the rear housing of the product. • Power cable of your product must comply with the values in "Technical specifications" table. As DANGER: •I BI•nesftoarlelatsiotanr,tidnigscaonnynwecotrkthoenptrhoeduecletcftrroicmalthe mains supply. There is the risk of electric shock! Connecting the power cable 1. This product must only be connected by a qualified electrician such as a technician from the local electricity company or NICEIC registered contractor to a suitable double-pole control unit with a minimum contact clearance of 3 mm in all poles. This control unit must be installed accordance with the IEE regulation. Failure to obey this instruction may cause operational problems and invalidate the product warranty. Additional protection by a residual current circuit breaker is recommended. If a cable is supplied with the product: II L1 L2 N 2N AC 380-415 V 1N AC 220-240 V 2. For single-phase connection, connect the wires as identified below: • Brown/Black cable = L (Phase) • Blue/Grey cable = N (Neutral) • Green/yellow cable = (E) = (Ground) 3. For double-phase connection, connect the wires as identified below: • Brown cable = L1 (Phase 1) • Black cable = L2 (Phase 2) • Blue/Grey cable = N (Neutral) • Green/yellow cable = (E) =I (Ground) » or • Black cable = L1 (Phase 1) • Grey cable = L2 (Phase 2) • Blue/Brown cable = N (Neutral) • Green/yellow cable = (E) 7.-7 (Ground) Installing the product If the oven is below: C C C C C 20 m C C E . E g in E C C C 1 0/EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
Our
company
shall
not
be
liable
for
any
damages
that
will
arise
due
to
using
the
product
without
a
grounding
installation
in
accordance
with
the
local
regulations.
A
.
a
DANGER:
I
The
product
must
be
connected
to
the
mains
supply
only
by
an
authorised
and
qualified
person.
The
product's
warranty
period
starts
only
after
correct
installation.
Manufacturer
shall
not
be
held
responsible
for
damages
arising
from
procedures
carried
out
by
unauthorised
persons.
"
DANGER:
"
The
power
cable
must
not
be
clamped,
bent
or
•
trapped
or
come
into
contact
with
hot
parts
of
the
product.
A
damaged
power
cable
must
be
replaced
by
a
qualified
electrician.
Otherwise,
there
is
risk
of
electric
shock,
short
circuit
or
fire!
•
Connection
must
comply
with
national
regulations.
•
The
mains
supply
data
must
correspond
to
the
data
specified
on
the
type
label
of
the
product.
Type
label
is
at
the
rear
housing
of
the
product.
•
Power
cable
of
your
product
must
comply
with
the
values
in
"Technical
specifications"
table.
A
s
DANGER:
I
Before
starting
any
work
on
the
electrical
•
•
Installation,
disconnect
the
product
from
the
mains
supply.
There
is
the
risk
of
electric
shock!
Connecting
the
power
cable
1.
This
product
must
only
be
connected
by
a
qualified
electrician
such
as
a
technician
from
the
local
electricity
company
or
NICEIC
registered
contractor
to
a
suitable
double
-pole
control
unit
with
a
minimum
contact
clearance
of
3
mm
in
all
poles.
This
control
unit
must
be
installed
accordance
with
the
IEE
regulation.
Failure
to
obey
this
instruction
may
cause
operational
problems
and
invalidate
the
product
warranty.
Additional
protection
by
a
residual
current
circuit
breaker
is
recommended.
If
a
cable
is
supplied
with
the
product:
L1
L2
N
2N
AC
380-415
V
II
1N
AC
220-240
V
2.
For
single-phase
connection,
connect
the
wires
as
identified
below:
•
Brown/Black
cable
=
L
(Phase)
•
Blue/Grey
cable
=
N
(Neutral)
•
Green/yellow
cable
=
(E)
=
(Ground)
3.
For
double
-phase
connection,
connect
the
wires
as
identified
below:
•
Brown
cable
=
L1
(Phase
1)
•
Black
cable
=
L2
(Phase
2)
•
Blue/Grey
cable
=
N
(Neutral)
•
Green/yellow
cable
=
(E)
=
I
(Ground)
»
or
•
Black
cable
=
L1
(Phase
1)
•
Grey
cable
=
L2
(Phase
2)
•
Blue/Brown
cable
=
N
(Neutral)
•
Green/yellow
cable
=
(E)
7.-7
(Ground)
Installing
the
product
If
the
oven
is
below:
C
C
C
C
C
C
C
C
C
C
20
m
E
.
E
g
in
E
1
0/EN