Beko WMB714422 User Manual - Page 14

ConnectIng water supply

Get Beko WMB714422 PDF manuals and user guides View all Beko WMB714422 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

4.4.4 Connecting water supply C The water supply pressure required to run the product is between 1 to 10 bars (0.1 - 1 MPa). It is necessary to have 10 - 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly. Attach a pressure reducing valve if water pressure is higher. If you are going to use the double water-inlet product as a single (cold) water-inlet unit, you must install the supplied stopper to the hot water valve before operating the product. (Applies for the products supplied with a blind stopper group.) A CAUTION: Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will get damaged or the product will switch to protection mode and will not operate. CAUTION: Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry. Connect the special water supply hoses supplied with the product to the water inlets on the product. Red hose (left) (max. 90 ºC) is for hot water inlet, blue hose (right) (max. 25 ºC) is for cold water inlet. Make sure that the hot and cold water taps are connected correctly when the product is being installed. Otherwise, your laundry will come out hot at the end of the washing process and wear out. 1 Tighten the nuts of the hose by hand. Never use a tool when tightening the nuts. 2 When hose connection is completed, check whether there is leak problems at the connection points by opening the taps fully. If any leaks occur, turn off the tap and remove the nut. Retighten the nut carefully after checking the seal. In order to prevent the water leaks and resultant damages, keep the taps closed when you do not use the product. 14 / EN Washing Machine / User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
14 / EN
Wash±ng Mach±ne / User’s Manual
4.4.4 ConnectIng water supply
C
The water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa).
It is necessary to have 10 – 80 liters of water flowing from the fully open tap in one minute to
have your machine run smoothly. Attach a pressure reducing valve if water pressure is higher.
If you are going to use the double water-inlet product as a single (cold) water-inlet unit,
you must install the supplied stopper to the hot water valve before operating the product.
(Applies for the products supplied with a blind stopper group.)
A
CAUT±ON:
Models with a single water inlet should not be connected to the hot water tap.
In such a case the laundry will get damaged or the product will switch to protection mode and
will not operate.
CAUT±ON:
Do not use old or used water inlet hoses on the new product. It may cause
stains on your laundry.
Connect the special water supply hoses supplied with the product to the
water inlets on the product. Red hose (left) (max. 90 ºC) is for hot water
inlet, blue hose (right) (max. 25 ºC) is for cold water inlet.
Make sure that the hot and cold water taps are connected correctly when
the product is being installed. Otherwise, your laundry will come out hot at
the end of the washing process and wear out.
1
Tighten the nuts of the hose by hand. Never use a tool when tightening the nuts.
2
When hose connection is completed, check whether there is leak problems at the
connection points by opening the taps fully. If any leaks occur, turn off the tap and
remove the nut. Retighten the nut carefully after checking the seal. In order to prevent
the water leaks and resultant damages, keep the taps closed when you do not use the
product.