Beko WR862441 User Manual - Page 35

CleanIng the body and control panel, 7.4 CleanIng the water Intake fIlters, 7.5 DraInIng

Get Beko WR862441 PDF manuals and user guides View all Beko WR862441 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

After every washing make sure that no foreign substance is left in the drum. If the holes on the bellow shown in the figure are blocked, open the holes using a toothpick. Foreign metal substances will cause rust stains in the drum. Clean the stains on the drum surface by using cleaning agents for stainless steel. Never use steel wool or wire wool. These will damage the painted, chromated and plastic surfaces. 4.7.3 Cleaning the body and control panel Wipe the body of the product with soapy water or non-corrosive mild gel detergents as necessary, and dry with a soft cloth. Use only a soft and damp cloth to clean the control panel. 4.7.4 Cleaning the water intake filters There is a filter at the end of each water intake valve at the rear of the product and also at the end of each water intake hose where they are connected to the tap. These filters prevent foreign substances and dirt in the water to enter the product. Filters should be cleaned as they do get dirty. 1. Close the taps. 2. Remove the nuts of the water intake hoses to access the filters on the water intake valves. Clean them with an appropriate brush. If the filters are too dirty, remove them from their places with a pliers and clean in this way. 3. Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under running water. 4. Replace the seals and filters carefully and tighten their nuts by hand. 4.7.5 Draining remaining water and cleaning the pump filter The filter system in your product prevents solid items such as buttons, coins and fabric fibers clogging the pump impeller during discharge of washing water. Thus, the water will be discharged without any problem and the service life of the pump will extend. If the product fails to drain water inside it, the pump filter is clogged. Filter must be cleaned whenever it is clogged or in every 3 months. Water must be drained off first to clean the pump filter. In addition, prior to transporting the product (e.g., when moving to another house) water should be drained completely. Washing Machine / User's Manual 35 / EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
35 / EN
Wash±ng Mach±ne / User’s Manual
After every washing make sure that no foreign substance is
left in the drum.
If the holes on the bellow shown in the figure are blocked,
open the holes using a toothpick.
Foreign metal substances will cause rust stains in the drum.
Clean the stains on the drum surface by using cleaning
agents for stainless steel.
Never use steel wool or wire wool. These will damage the
painted, chromated and plastic surfaces.
4.7.3 CleanIng the body and control panel
Wipe the body of the product with soapy water or non-corrosive mild gel detergents as
necessary, and dry with a soft cloth.
Use only a soft and damp cloth to clean the control panel.
4.7.4 CleanIng the water Intake fIlters
There is a filter at the end of each water intake valve at the rear of the product and also
at the end of each water intake hose where they are connected to the tap. These filters
prevent foreign substances and dirt in the water to enter the product. Filters should be
cleaned as they do get dirty.
1.
Close the taps.
2.
Remove the nuts of the water intake hoses to access the filters on the water intake
valves. Clean them with an appropriate brush. If the filters are too dirty, remove them
from their places with a pliers and clean in this way.
3.
Take out the filters on the flat ends of the water intake hoses together with the
gaskets and clean thoroughly under running water.
4.
Replace the seals and filters carefully and tighten their nuts by hand.
4.7.5 DraInIng remaInIng water and cleanIng the pump fIlter
The filter system in your product prevents solid items such as buttons, coins and fabric
fibers clogging the pump impeller during discharge of washing water. Thus, the water will
be discharged without any problem and the service life of the pump will extend.
If the product fails to drain water inside it, the pump filter is clogged. Filter must be
cleaned whenever it is clogged or in every 3 months. Water must be drained off first to
clean the pump filter.
In addition, prior to transporting the product (e.g., when moving to another house) water
should be drained completely.