Belkin F8Z295 User Manual - Page 22

Belkin F8Z295 Manual

Get Belkin F8Z295 PDF manuals and user guides View all Belkin F8Z295 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Troubleshooting Table of Contents sections 1 2 3 4 5 6 Most problems with your GoStudio can be solved quickly by following the advice in this chapter. If you continue to have trouble, contact Belkin Customer Service at 800-223-5546 ext. 2263 or on the web at http://www.belkin.com/ support. If you don't hear anything in the speaker or headphones: Make sure your GoStudio is powered and the power switch is in the on position. Make sure the headphone cable is securely connected. Turn up the level control(s). Remember that the speaker is only used when playing back audio from an iPod. The speaker is not used to listen to your audio inputs in real time. If your GoStudio won't turn on: • Make sure you're using new AAA batteries or an AC power supply that meets the requirements listed in the "Specifications" section of this manual. You may damage your GoStudio and/or your iPod if you do not use a compatible power supply. Make sure the GoStudio's power switch is set to the on position. Or, if the power switch is set to the on with iPod position, make sure your iPod is awake and operational. Try using another power outlet. • If these suggestions don't help, you might have a bad cable. Check all of your cables and try replacing them with known good ones. • If the microphone volume is too low: Make sure the cables are securely connected. If the microphone is connected, or you're using the on-board mics, turn up the gain control switch. Consider moving the microphones closer to the audio source. GoStudio 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
20
GoStudio
Table of Contents
SECTIONS
1
2
3
4
5
6
TROUBLESHOOTING
Most problems with your GoStudio can be solved quickly by
following the advice in this chapter.
If you continue to have trouble, contact Belkin Customer Service at
800-223-5546 ext. 2263
or on the web at
support.
If your GoStudio won’t turn on:
•
Make sure you’re using new AAA batteries or an AC power supply
that meets the requirements listed in the “Specifications” section of
this manual. You may damage your GoStudio and/or your iPod if you
do not use a compatible power supply.
•
Make sure the GoStudio’s power switch is set to the
on
position. Or,
if the power switch is set to the
on with iPod
position, make sure
your iPod is awake and operational.
•
Try using another power outlet.
If you don’t hear anything in the speaker or
headphones:
•
Make sure your GoStudio is powered and the power switch is in the
on position.
•
Make sure the headphone cable is securely connected.
•
Turn up the level control(s).
•
Remember that the speaker is only used when playing back audio
from an iPod. The speaker is not used to listen to your audio inputs
in real time.
If these suggestions don’t help, you might have a bad cable. Check all of
your cables and try replacing them with known good ones.
If the microphone volume is too low:
•
Make sure the cables are securely connected.
•
If the microphone is connected, or you’re using the on-board mics,
turn up the gain control switch.
•
Consider moving the microphones closer to the audio source.