Belkin F8Z295 User Manual - Page 69

Belkin F8Z295 Manual

Get Belkin F8Z295 PDF manuals and user guides View all Belkin F8Z295 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

DESCRIPCIó GENERAL Table des matières Contenido secciones sections 1 2 3 4 5 6 8 9 Coloque los interruptores opcionales mono, limiter (limitador), y low cut filter (filtro de corte bajo) en la posición off (apagado). Estos controles se localizan en el lado derecho del panel de control. Let's do a quick level check. Gently tap on one of the GoStudio's microphones. You should see some of the GoStudio's recording level LEDs, located above the master level control knob, light up when you tap the microphone. This lets you know that the audio signal is ready to be recorded. Find the right adapter for your iPod type and install the adapter in the GoStudio cradle. Some iPod models don't require an adapter. Slide your iPod into the cradle and gently push down on your iPod so that it connects to the GoStudio. Some iPod models will automatically transition to the iPod Voice Memo interface. If your iPod does not automatically transition to the Voice Memo interface, then you'll have to navigate to it using the iPod click wheel. From your iPod main menu, select the Voice Memos option. Using the iPod interface and controls, start recording. Note that the GoStudio's status indicator changes to red when your iPod is recording. Now make some noise into the GoStudio's microphones. Tap the microphones, speak into the microphones, or find someone else to speak into the microphones. Once you're done, use your iPod controls to end the recording. Now your iPod should show a list of recordings, which are shown as a time stamp of when the recording was made. In this case, the recording you just made might be the only recording in the list. Scroll to the new recording and press the play/pause button on your iPod click wheel. You should be able to hear your recording through the GoStudio's speaker, which is located on the lower-right side of the control panel. If you can't hear anything, turn up the monitor level control knob, which is located on the lower-left side of the control panel. That's it! You've made your first recording. Now that you understand the GoStudio's basic controls, you'll be able to set up and record much more quickly in the future. Go to www.belkin.com/registration to register your GoStudio. 10 11 12 13 14 15 16 17 18 GoStudio 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
67
GoStudio
8
Coloque los interruptores opcionales
mono
,
limiter
(limitador), y
low cut filter
(filtro de corte bajo) en la posición
off
(apagado). Estos controles se
localizan en el lado derecho del panel de control.
9
Let’s do a quick level check. Gently tap on one of the GoStudio’s microphones. You should see some of the GoStudio’s recording level LEDs,
located above the
master level
control knob, light up when you tap the microphone. This lets you know that the audio signal is ready to be
recorded.
10
Find the right adapter for your iPod type and install the adapter in the GoStudio cradle. Some iPod models don’t require an adapter.
11
Slide your iPod into the cradle and gently push down on your iPod so that it connects to the GoStudio.
12
Some iPod models will automatically transition to the iPod Voice Memo interface. If your iPod does not automatically transition to the Voice Memo
interface, then you’ll have to navigate to it using the iPod click wheel. From your iPod main menu, select the
Voice Memos
option.
13
Using the iPod interface and controls, start recording. Note that the GoStudio’s status indicator changes to red when your iPod is recording.
14
Now make some noise into the GoStudio’s microphones. Tap the microphones, speak into the microphones, or find someone else to speak into the
microphones.
15
Once you’re done, use your iPod controls to end the recording.
16
Now your iPod should show a list of recordings, which are shown as a time stamp of when the recording was made. In this case, the recording
you just made might be the only recording in the list. Scroll to the new recording and press the play/pause button on your iPod click wheel. You
should be able to hear your recording through the GoStudio’s speaker, which is located on the lower-right side of the control panel. If you can’t hear
anything, turn up the
monitor level
control knob, which is located on the lower-left side of the control panel.
17
That’s it! You’ve made your first recording. Now that you understand the GoStudio’s basic controls, you’ll be able to set up and record much more
quickly in the future.
18
Go to
www.belkin.com/registration
to register your GoStudio.
Table des matières
SECTIONS
1
2
3
4
5
6
DESCRIPCIÓ GENERAL
Contenido
SECCIONES
1
2
3
4
5
6