BenQ MS513 MS513, MX514, MW516 User Manual - Page 61

Timing of replacing the lamp, Status, Message

Get BenQ MS513 PDF manuals and user guides View all BenQ MS513 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Timing of replacing the lamp When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode. Do not attempt to replace the lamp yourself. Contact the qualified service personnel for replacement. The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot. See "Indicators" on page 65 for details. The following lamp warning displays will remind you to change the lamp. The warning messages below are for reference only. Please follow the actual on-screen instructions to prepare and replace the lamp. Status Message Install a new lamp for optimal performance. If the projector is normally run with Economic selected ("Setting Lamp mode eco function as Economic or Smart Eco mode" on page 60), you may continue to operate the projector until the next lamp warning appears. A new lamp should be fitted to avoid the inconvenience when the projector runs out of lamp time. It is strongly recommended that you replace the lamp at this stage. The lamp is a consumable item. The lamp brightness diminishes with use. This is normal lamp behavior. You can replace the lamp whenever you notice that the brightness level has significantly diminished. The lamp MUST be replaced before the projector will operate normally. "XXXX" shown in the above messages are numbers that vary depending on different models. Maintenance 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Maintenance
61
Timing of replacing the lamp
When the
Lamp indicator
lights up red or a message appears suggesting it is time to
replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a
malfunction in the projector and in some instances the lamp may explode.
Do not attempt to replace the lamp yourself. Contact the qualified service personnel for
replacement.
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too
hot. See
"Indicators" on page 65
for details.
The following lamp warning displays will remind you to change the lamp.
The warning messages below are for reference only. Please follow the actual on-screen
instructions to prepare and replace the lamp.
"XXXX" shown in the above messages are numbers that vary depending on different models.
Status
Message
Install a new lamp for optimal performance. If the
projector is normally run with
Economic
selected (
"Setting Lamp mode eco function as
Economic or Smart Eco mode" on page 60
), you
may continue to operate the projector until the
next lamp warning appears.
A new lamp should be fitted to avoid the
inconvenience when the projector runs out of
lamp time.
It is strongly recommended that you replace the
lamp at this stage. The lamp is a consumable item.
The lamp brightness diminishes with use. This is
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished.
The lamp MUST be replaced before the projector
will operate normally.