BenQ PW9620 DLP Projector User Manual - Page 22

Connect to video equipment, Connect to control port

Get BenQ PW9620 DLP Projector PDF manuals and user guides View all BenQ PW9620 DLP Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

English Connect to video equipment You may connect any video equipment to your projector's input port with a DVI-D, HDMI, DisplayPort or YPBPR cable. Connect to control port Your projector features the following control ports: 3D sync signal transmitter (IR) • HD CONNECT/LAN Your projector supports network control with shared LAN (network control) and HD Connect. • RS-232 (RS-232c control) Your projector supports RS-232c serial control,You may connect the projector to a PC with standard 9-pin serial cable (straight through wire) for remote control. • Wired controller If the remote controller's IR signal fails to reach your projector because the two are too far apart or blocked by any obstacle, you may connect the WIRE input port of your projector to an IR remote controller or an (optional) IR repeater to expand its working area. • 3D Sync Out 3D IR sync signal transmitter Caution: • The projector enters wired control mode automatically and cannot be controlled by a remote controller's IR signal once the terminal of a remote controller is inserted in the projector's wire port. To control your projector with the IR signal of a remote controller again, remove the wire control terminal from the projector. • Make sure the port is valid before inserting a wired remote controller.The remote controller may be damaged if a Downloaded From projpeoctrotri-smiannvualaidl.,ceo.mg. Ba ewniQreMd arenmuaolste controller is connected to trigger output. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
English
22
Connect to video equipment
You may connect any video equipment to your projector’s input port with a DVI-D, HDMI,
DisplayPort or YPBPR cable.
Connect to control port
Your projector features the following control ports:
3D sync signal
transmitter (IR)
•
HD CONNECT/LAN
Your projector supports network control with shared LAN (network control) and HD Connect.
•
RS-232 (RS-232c control)
Your projector supports RS-232c serial control,You may connect the projector to a PC with
standard 9-pin serial cable (straight through wire) for remote control.
•
Wired controller
If the remote controller’s IR signal fails to reach your projector because the two are too far
apart or blocked by any obstacle, you may connect the WIRE input port of your projector to an
IR remote controller or an (optional) IR repeater to expand its working area.
•
3D Sync Out
3D IR sync signal transmitter
Caution:
•
The projector enters wired control mode automatically and cannot be controlled by a remote controller’s IR signal
once the terminal of a remote controller is inserted in the projector’s wire port. To control your projector with
the IR signal of a remote controller again, remove the wire control terminal from the projector.
•
Make sure the port is valid before inserting a wired remote controller. The remote controller may be damaged if a
port is invalid, e.g. a wired remote controller is
connected to trigger output.
Downloaded From projector-manual.com BenQ Manuals