Biostar I915P-A7 I915P-A7 BIOS guide. - Page 22

Super IO Device, Onboard FDC Controller, Onboard Serial Port 1, Onboard Serial Port 2, UART Mode

Get Biostar I915P-A7 PDF manuals and user guides View all Biostar I915P-A7 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

1915P-A7 BIOS Manual 5.3 Super IO Device If you highlight the literal "Press Enter" next to the "Super IO Device" label and then press the enter key, it will take you a submenu with the following options: 5.3.1 Onboard FDC Controller Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If install and FDC or the system has no floppy drive, select Disabled in this field. The Choices: Enabled (default), Disabled. 5.3.2 Onboard Serial Port 1 Select an address and corresponding interrupt for the first and second serial ports. The Choices:Disabled, 3F8/IRQ4 (default), 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3, Auto. 5.3.3 Onboard Serial Port 2 Select an address and corresponding interrupt for the first and second serial ports. The Choices:Disabled, 2F8/IRQ3 (default), 3F8/IRQ4, 3E8/IRQ4, 2E8/IRQ3, Auto. 5.3.4 UART Mode Select This item allows you to determine which Infra Red (IR) function of onboard I/O chip. The Choices:Normal (default), AS KIR, IrDA. 5.3.5 UR2 Duplex Mode elect the value required by the IR device connected to the IR port. Full-duplex mode permits simultaneous two-direction transmission. Half-duplex mode permits transmission in one direction only at a time. The Choices: Half (default), Full. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
1915P-A7 BIOS Manual
21
5.3 Super IO Device
If you highlight the literal “Press Enter” next to the “
Super IO Device
” label and then press the
enter key, it will take you a submenu with the following options:
5.3.1
Onboard FDC Controller
Select Enabled if your system has a floppy disk controller (FDC) installed on the system
board and you wish to use it. If install and FDC or the system has no floppy drive, select
Disabled in this field.
The Choices: Enabled
(default), Disabled.
5.3.2
Onboard Serial Port 1
Select an address and corresponding interrupt for the first and second serial ports.
The Choices:
Disabled,
3F8/IRQ4
(default), 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3, Auto.
5.3.3
Onboard Serial Port 2
Select an address and corresponding interrupt for the first and second serial ports.
The Choices:
Disabled,
2F8/IRQ3
(default), 3F8/IRQ4, 3E8/IRQ4,
2E8/IRQ3, Auto.
5.3.4
UART Mode Select
This item allows you to determine which Infra Red (IR) function of onboard I/O chip.
The Choices:Normal
(default), AS KIR, IrDA.
5.3.5
UR2 Duplex Mode
elect the value required by the IR device connected to the IR port. Full-duplex mode
permits simultaneous two-direction transmission. Half-duplex mode permits transmission
in one direction only at a time.
The Choices: Half
(default), Full.