Biostar IDEQ 220K BIOS MANUAL - Page 27

Super IO Device, Onboard FDC Controller, Onboard Serial Port 1, Onboard Serial Port 2, UART Mode

Get Biostar IDEQ 220K PDF manuals and user guides View all Biostar IDEQ 220K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

K8VBK-S7 BIOS Setup 5.3 Super IO Device 5.3.1 5.3.2 5.3.3 5.3.4 If you highlight the literal "Press Enter" next to the "Super IO Device" label and then press the enter key, it will take you a submenu with the following options: Onboard FDC Controller Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If install and FDC or the system has no floppy drive, select Disabled in this field. The Choices: Enabled (default), Disabled. Onboard Serial Port 1 Select an address and corresponding interrupt for the first and second serial ports. The Choices: Disabled, 3F8/IRQ4 (default), 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3, Auto. Onboard Serial Port 2 Select an address and corresponding interrupt for the first and second serial ports. The Choices: Disabled, 2F8/IRQ3 (default), 3F8/IRQ4, 3E8/IRQ4, 2E8/IRQ3, Auto. UART Mode Select This item allows you to determine which Infra Red (IR) function of onboard I/O chip. The Choices: Normal (default), AS KIR, IrDA. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
K8VBK-S7 BIOS Setup
26
5.3 Super IO Device
If you highlight the literal “Press Enter” next to the “
Super IO Device
” label and then
press the enter key, it will take you a submenu with the following options:
5.3.1
Onboard FDC Controller
Select Enabled if your system has a floppy disk controller (FDC) installed on the system
board and you wish to use it. If install and FDC or the system has no floppy drive, select
Disabled in this field.
The Choices: Enabled
(default), Disabled.
5.3.2
Onboard Serial Port 1
Select an address and corresponding interrupt for the first and second serial ports.
The Choices:
Disabled,
3F8/IRQ4
(default), 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3, Auto.
5.3.3
Onboard Serial Port 2
Select an address and corresponding interrupt for the first and second serial ports.
The Choices:
Disabled,
2F8/IRQ3
(default), 3F8/IRQ4, 3E8/IRQ4,
2E8/IRQ3, Auto.
5.3.4
UART Mode Select
This item allows you to determine which Infra Red (IR) function of onboard I/O chip.
The Choices:
Normal
(default), AS KIR, IrDA.