Bissell ProHeat Pet Deep Cleaning System 89104 User Guide - English - Page 10

Set ready tools dial, Power switch, Cleaning strokes

Get Bissell ProHeat Pet Deep Cleaning System 89104 PDF manuals and user guides View all Bissell ProHeat Pet Deep Cleaning System 89104 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Operation Set ready tools dial Set ready tools dial to floor cleaning. Power switch ReadyTools Dial 1. Plug into a proper outlet and turn the power and heater switches to the ON ( I ) position. The switches are found on the back of the handle. Allow 1 minute for the built-in heater to warm-up before cleaning. The ProHeat will be fully warmed and will provide optimal performance after a minute of continuous heated cleaning. 2. The SmartTemp ready light indicates when the heater is ON ( I ). Note: SmartTemp heats the cleaning solution for carpet and hard floor application only. It does not heat solution sprayed through the accessory tools. Cleaning strokes 1. While pressing the trigger, make one slow forward wet pass and another one back. Let the built-in heater, formula, and DirtLifter PowerBrush do the work for you. Caution: Do not overwet. Take care not to run over loose objects, edges of area rugs, or the cord. Stalling brush may result in premature belt failure. Tip: Deep Cleaning stairs and heavy traffic areas on a regular basis can prolong carpet life. FLCOLOERANING PRTEOTORLESAT Power Switch 1. SmartTemp Switch ON OFF ON OFF SmartTemp Light 2. 2. Release the trigger and make one slow forward and backward pass over the same area to remove any residual dirty water, and aid in drying. Repeat cleaning passes until solution being pulled up appears clean. Continue passes without pressing the trigger until you can't see any more water being pulled up. NOTE: Both the SmartMix tank and the clean water tank must have liquid in them in order for the machine to spray. If one tank is empty the machine will not apply cleaning solution or water. WARNING: To reduce the risk of fire, electric shock or injury, unplug from the outlet before servicing. 3. After cleaning, you may want to turn the SmartMix dial to water rinse to give your carpeting a final water only rinse. This will ensure thorough removal of embedded dirt loosened by the deep cleaning formula. BISSELL deep cleaning formulas contain an anti-resoiling agent that helps your carpets repel dirt and keeps them looking good longer. 10 w w w . b i s s e l l . c o m 800.237.7691 ug120-4080_7350_908.indd 10 10/14/08 1:26:59 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
10
www.bissell.com
800.237.7691
O
peration
Set ready tools dial
Set ready tools dial to floor cleaning.
Power switch
1.
Plug into a proper outlet and turn the power
and heater switches to the
ON ( I )
position.
The switches are found on the back of the
handle. Allow 1 minute for the built-in heater
to warm-up before cleaning. The ProHeat
will be fully warmed and will provide optimal
performance after a minute of continuous
heated cleaning.
2.
The SmartTemp ready light indicates when
the heater is
ON ( I )
.
Note: SmartTemp heats the cleaning solution
for carpet and hard floor application only. It
does not heat solution sprayed through the
accessory tools.
Cleaning strokes
1.
While pressing the trigger, make one slow
forward wet pass and another one back. Let
the built-in heater, formula, and DirtLifter
PowerBrush do the work for you.
Caution:
Do
not overwet.
Take care not to run over loose
objects, edges of area rugs, or the cord. Stalling
brush may result in premature belt failure.
2.
Release the trigger and make one slow forward
and backward pass over the same area to
remove any residual dirty water, and aid in
drying. Repeat cleaning passes until solution
being pulled up appears clean. Continue passes
without pressing the trigger until you can’t see
any more water being pulled up.
NOTE: Both the SmartMix tank and the
clean water tank must have liquid in them
in order for the machine to spray. If one
tank is empty the machine will not apply
cleaning solution or water.
3.
After cleaning, you may want to turn the
SmartMix dial to water rinse to give your
carpeting a final water only rinse. This will
ensure thorough removal of embedded dirt
loosened by the deep cleaning formula.
BISSELL deep cleaning formulas contain an
anti-resoiling agent that helps your carpets
repel dirt and keeps them looking good longer.
ReadyTools Dial
Tip:
Deep Cleaning stairs and heavy traffic areas
on a regular basis can prolong carpet life.
SmartTemp Light
ON
OFF
Power Switch
SmartTemp Switch
WARNING:
To reduce the risk of fire,
electric shock or injury,
unplug from the outlet
before servicing.
1.
2.
ug120-4080_7350_908.indd
10
10/14/08
1:26:59 PM