Bissell ProHeat Pet Deep Cleaning System 89104 User Guide - English - Page 17

roubleshooting

Get Bissell ProHeat Pet Deep Cleaning System 89104 PDF manuals and user guides View all Bissell ProHeat Pet Deep Cleaning System 89104 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Troubleshooting Reduced spray or no spray. Possible Cause Remedies 1. Bladder may be empty. 1. Refill bladder with hot tap water. 2. SmartMix tank may be empty. 2. Fill with BISSELL deep Cleaning formula for cleaning. Fill with water if rinsing. 3. The filter may be clogged. 3. Clean out flow indicator filter, page 12. 4. Tanks may not be seated properly. 4. Turn power OFF (O); remove & reseat tanks. 5. Pump may have lost prime. 5. Turn power OFF (O); after 1 minute turn ON and press trigger. 6. The Pump belt may be broken. 6. Turn on the machine and check to see that the DirtLifter PowerBrush turns. If it does not, refer to #1 below. DirtLifter PowerBrush does not turn. Possible Cause Remedies 1. The brush belt or pump belt 1. Turn the machine OFF (O) and unplug is off or broken. from the outlet. To check if the brush belt or pump belt has broken, you will need a flat head screwdriver. Insert the blade end into the lower slot of the belt access door to release the lower snap. If necessary, insert the blade end into the upper slot to release the upper snap. Examine the belt for breakage. If broken, please refer to Replacement Parts on page 19 Lift He re before calling Consumer Services. Complete installation instructions Insert will accompany the replacement belt. Screwdriver Blade Here Cleaner not picking up solution. Possible Causes Remedies 1. ReadyTools dial may be on the 1. Set ReadyTools dial to either floor wrong setting for the cleaning job. cleaning or tools. 2. Nozzle window may not be 2. Press down firmly on the black properly attached. oval gasket at the top window to make sure the two tabs on the back of the nozzle window are snapped into the mating slots in the main housing. 3. Tank-in-tank lid is not properly installed. 3. Re-install lid; refer to page 9. 4. Tank-in-tank is not properly seated. 4. Tank-in-tank must be firmly seated to function; remove and reseat tank-in-tank. www.bissell.com 800.237.7691 17 ug120-4080_7350_908.indd 17 10/14/08 1:27:04 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
T
roubleshooting
Reduced spray or no spray.
Possible Cause
Remedies
1.
Bladder may be empty.
1.
Refill bladder with hot tap water.
2.
SmartMix tank may be empty.
2.
Fill with BISSELL deep Cleaning
formula for cleaning. Fill with
water if rinsing.
3.
The filter may be clogged.
3.
Clean out flow indicator filter,
page 12.
4.
Tanks may not be seated properly.
4.
Turn power OFF
(O)
; remove &
reseat tanks.
5.
Pump may have lost prime.
5.
Turn power OFF
(O)
; after 1
minute turn ON and press
trigger.
6.
The Pump belt may be broken.
6.
Turn on the machine and check to see
that the DirtLifter PowerBrush turns. If
it does not, refer to #1 below.
DirtLifter PowerBrush does not turn.
Possible Cause
Remedies
1.
The brush belt or pump belt
1. Turn the machine
OFF (O)
and unplug
is off or broken.
from the outlet. To check if the brush
belt or pump belt has broken, you
will need a flat head screwdriver.
Insert the blade end into the lower
slot of the belt access door to release
the lower snap. If necessary, insert
the blade end into the upper slot to
release the upper snap. Examine the
belt for breakage. If broken, please
refer to Replacement Parts on page 19
before calling Consumer Services.
Complete installation instructions
will accompany the replacement belt.
Cleaner not picking up solution.
Possible Causes
Remedies
1. ReadyTools dial may be on the
1. Set ReadyTools dial to either floor
wrong setting for the cleaning job.
cleaning or tools.
2. Nozzle window may not be
2. Press down firmly on the black
properly attached.
oval gasket at the top window to
make sure the two tabs on the
back of the nozzle window are
snapped into the mating slots in
the main housing.
3.
Tank-in-tank lid is not properly installed.
3.
Re-install lid; refer to page 9.
4.
Tank-in-tank is not properly seated.
4.
Tank-in-tank must be firmly
seated to function; remove and
reseat tank-in-tank.
Insert
Screwdriver
Blade Here
Lift Here
17
www.bissell.com
800.237.7691
ug120-4080_7350_908.indd
17
10/14/08
1:27:04 PM