Bosch B09IB80NSP Instructions for Use - Page 18

Eliminating minor faults yourself

Get Bosch B09IB80NSP PDF manuals and user guides View all Bosch B09IB80NSP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

en-us Eliminating minor faults yourself Before you call customer service: Please check whether you can eliminate the fault yourself based on the following information. Customer service will charge you for advice -even if the appliance is still under guarantee! Fault Temperature differs greatly from the set value. Displays do not illuminate. Temperature display indicates "E..". Warning signal sounds, alarm button 2 lights up.5 The freezer compartment is too warm! Frozen food is at risk! Freezer compartment temperature display 4 flashes. Warning signal sounds The alarm button 5 is lit. The freezer compartment is too warm! Frozen food is at risk! Temperature display for the freezer section 5 flashes.4 Appliance is not cooling, temperature display and light are lit. Possible cause Power failure; the fuse has been switched off; the power cord plug has not been inserted properly. Electronics have detected a fault. Remedial action In some cases it is adequate to switch off the appliance for 5 minutes. If the temperature is too high wait a few hours and check whether the temperature has approached the set value. If the temperature is too low check the temperature again the next day. Connect power cord plug. Check whether the power is on, check the fuses. Call customer service. To switch off the warning signal, press the alarm button 5. Appliance is open. Close the appliance. Ventilation openings have been cov- Ensure that there is adequate ventilation. ered. Large quantities of fresh food are being frozen. Freeze less fresh food. When the fault has been eliminated, the alarm button 5goes out shortly afterwards. To switch off the warning signal, press the alarm button 5. Appliance is open. Close the appliance. Ventilation openings have been cov- Ensure that there is adequate ventilation. ered. Large quantities of fresh food are being frozen. Freeze less fresh food. When the fault has been eliminated, the alarm display goes out shortly afterwards. A fault caused the freezer section When the alarm button 5 is pressed, the temto become too warm in the past. perature display 4 stops flashing. The temperature display indicates for five seconds the warmest temperature which was reached in the freezer section. Showroom mode is switched on. Start appliance self-test (see chapter "Appliance self-test"). When the program has ended, the appliance switches over to normal operation. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
en-us
18
Eliminating minor faults yourself
Before you call customer service:
Please check whether you can eliminate the fault yourself based on the following information.
Customer service will charge you for advice
–
even if the appliance is still under guarantee!
Fault
Possible cause
Remedial action
Temperature differs greatly
from the set value.
In some cases it is adequate to switch off
the appliance for 5 minutes.
If the temperature is too high wait a few hours
and check whether the temperature has
approached the set value.
If the temperature is too low check
the temperature again the next day.
Displays do not illuminate.
Power failure;
the fuse has been switched off;
the power cord plug has not been
inserted properly.
Connect power cord plug. Check whether
the power is on, check the fuses.
Temperature display indi-
cates “E..”.
Electronics have detected a fault.
Call customer service.
Warning signal sounds,
alarm button 2 lights up.5
The freezer compartment is
too warm!
Frozen food is at risk!
To switch off the warning signal, press the alarm
button 5.
Appliance is open.
Close the appliance.
Ventilation openings have been cov-
ered.
Ensure that there is adequate ventilation.
Large quantities of fresh food are
being frozen.
Freeze less fresh food.
When the fault has been eliminated, the alarm
button 5goes out shortly afterwards.
Freezer compartment tem-
perature display 4 flashes.
Warning signal sounds
The alarm button 5 is lit.
The freezer compartment is
too warm!
Frozen food is at risk!
To switch off the warning signal, press the alarm
button 5.
Appliance is open.
Close the appliance.
Ventilation openings have been cov-
ered.
Ensure that there is adequate ventilation.
Large quantities of fresh food are
being frozen.
Freeze less fresh food.
When the fault has been eliminated, the alarm
display goes out shortly afterwards.
Temperature display for
the freezer section 5
flashes.4
A fault caused the freezer section
to become too warm in the past.
When the alarm button 5 is pressed, the tem-
perature display 4 stops flashing.
The temperature display indicates for five sec-
onds the warmest temperature which was
reached in the freezer section.
Appliance is not cooling,
temperature display and
light are lit.
Showroom mode is switched on.
Start appliance self-test (see chapter “Appliance
self-test”).
When the program has ended, the appliance
switches over to normal operation.