Bosch B36IT71SNS Instructions for Use - Page 20

Warning, messages, via²the display

Get Bosch B36IT71SNS - 20 cu. Ft. Refrigerator PDF manuals and user guides
UPC - 825225867333
View all Bosch B36IT71SNS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Warning messages via the display If several warning messages are displayed simultaneously, deal with each message individually. While a warning message is displayed, buttons cannot be pressed.15. Temperature alarm (freezer compartment) Door alarm Cause - An appliance door has not been closed properly or has been open too long. Remedial action q Close the door. The display goes out. Sensor fault Appliance selfĆtest Before you call customer service, conduct an appliance selfĆtest. q Switch off the appliance and wait 5 minutes. Keep the door closed. q Switch on the appliance. A temperature alarm is indicated by the required temperature flashing and the ALARM symbol coming on. A signal also sounds if the Tone function has been activated in setup mode. Cause - Power failure - Large quantities of fresh produce placed in the appliance - Fault with the appliance Remedial action q Press the alarm button. The signal stops. The highest temperature in the appliance is displayed for several seconds. q Determine the cause of the temperature alarm. i When the required temperature is reached again, the ALARM symbol goes out and the signal stops. Cause - A technical defect is possible. Remedial action q Conduct an appliance selfĆtest. Low voltage The display light has gone out. Cause - The mains voltage has dropped below the permitted limit value. Remedial action Buttons cannot be pressed. When the mains voltage reaches the stipulated value again, the warning message goes out. If the warning message is prolonged, inform your power supply company. q Simultaneously hold down the setup and alarm off buttons for 5 seconds. The selfĆtest starts. Different messages are display in succession. If a fault is detected during the selfĆtest, the ALARM symbol and a corresponding error message, e.g. for a sensor fault, are displayed. Inform customer service about the error message. If the appliance selfĆtest does not establish any faults, the required temperature is displayed on completion of the selfĆtest. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
20
Warning
messages
via²the display
If
several warning
messages
are
displayed
simultaneously,
deal
with
each
message individually.
While a
warning
message
is
displayed, buttons cannot
be
pressed.
15.
Temperature alarm
(freezer compartment)
A temperature alarm
is
indicated by
the required
temperature
flashing
and the
ALARM
symbol coming on.
A signal also
sounds if
the
Tone
function has been
activated in
setup
mode.
Cause
-
Power
failure
-
Large quantities of
fresh
produce placed
in
the
appliance
-
Fault with
the appliance
Remedial action
q
Press
the
alarm
button.
The
signal stops. The highest
temperature in
the
appliance
is
displayed
for several
seconds.
q
Determine the cause of
the
temperature alarm.
i
When
the required temperature
is
reached
again,
the
ALARM
symbol goes out
and the
signal
stops.
Door alarm
Cause
-
An appliance door has not
been
closed
properly or
has been
open too
long.
Remedial action
q
Close the door.
The display goes out.
Sensor fault
Cause
-
A technical defect
is possible.
Remedial action
q
Conduct an appliance selfĆtest.
Low voltage
The display light has gone out.
Cause
-
The mains voltage has dropped
below
the permitted
limit value.
Remedial action
Buttons cannot
be pressed. When
the
mains voltage
reaches the
stipulated
value again, the warning
message
goes out. If
the warning
message is prolonged, inform
your
power
supply company.
Appliance
selfĆtest
Before you call customer service,
conduct an appliance
selfĆtest.
q
Switch off
the appliance and
wait 5
minutes. Keep the
door
closed.
q
Switch on the appliance.
q
Simultaneously hold down
the
setup
and
alarm off
buttons for
5
seconds.
The selfĆtest
starts. Different
messages
are display in succession.
If
a fault is detected
during the
selfĆtest,
the
ALARM
symbol
and a
corresponding
error message,
e.g.±for
a
sensor
fault, are
displayed.
Inform
customer
service
about
the
error
message.
If
the appliance selfĆtest
does not
establish any
faults, the required
temperature is displayed on
completion of
the selfĆtest.