Home » Bosch Manuals » Security Cameras » Bosch DB18C3100R2 » Manual Viewer

Bosch DB18C3100R2 Installation Guide - Page 134

Connecting the MINITER RS 485 Foyer Card Reader

Add to My Manuals
Save this manual to your list of manuals

Page 134 highlights

134 en | Connections DiBos/DiBos Micro 9.7 Connecting the MINITER RS 485 Foyer Card Reader The MINITER RS 485 foyer card reader is connected via a serial interface. A maximum of four foyer card readers can be connected in series. It is possible to operate the LS23M and the MINITER RS 485 foyer card readers on the same serial bus. Note that the LS23M foyer card reader should preferably be installed as the last bus element. 1 4 10 22 11 2 5 23 3 19 21 13 25 14 6 4 5 7 8 4 5 1 Video system 5 RS232 2 COM x 6 Foyer card reader 1 (MINITER RS 485) (4.998.098.769 / 4.998.098.767) 3 Connection cable, 9-pin - 25-pin 7 Per wire 2 x 0.6 mm 4 Interface converter W&T 86000 8 Foyer card reader 4 (LS23M), J2 (4.998.053.926) connected NOTICE! - The distance between the interface converter and the last foyer card reader can be a maximum of 1000 m (installation cable J-Y(St) Y 2 x 2 x 0.6 mm). - The foyer card reader must be correctly grounded! - Shielding may only be applied on one side. - The connection between the foyer card readers may only be made via the connector strip of the reader. - If the last foyer card reader on the RS 485 bus is a MINITER, the RS 485 bus must always be terminated with a 250 Ohm termination resistor (resistor is included in delivery). - For flush mounting: At the rear of the housing, the angle bracket that the credit card hits must be cut off. Only then is the credit card data read correctly. For further information on how the interface converter works, see the description W&T Interface Model 86000. F.01U.033.308 | V7 | 2009.09 Installation Guide Bosch Sicherheitssysteme GmbH

Section	Page
1 Safety Notes	7
2 Introduction	11
2.1 System Description	11
2.2 Unpacking	11
2.3 Power	11
2.4 Environmental	11
2.5 Recommended Virus Scanners/Firewall	12
2.5.1 Virus Scanners	12
2.5.2 Firewall	12
2.6 System Overview/Technical Specifications	14
2.6.1 DiBos	14
2.6.2 DiBos micro	18
3 Device Connections	21
3.1 DiBos	21
3.1.1 DiBos Front View	21
3.1.2 DiBos Rear View	22
3.1.3 Grabber Card for DiBos	23
3.1.4 I/O Card for DiBos	24
3.2 DiBos micro	25
3.2.1 DiBos micro Front View	25
3.2.2 DiBos micro Rear View	26
3.2.3 Grabber Card for DiBos micro	27
3.2.4 I/O Card (for DiBos micro)	28
4 Quick Installation	30
5 Quick Configuration	31
5.1 General Settings	31
5.2 Creating a User	33
5.3 Setting up the Network	34
5.4 Specifying Cameras	36
5.5 Assigning Time Profiles	37
5.6 Setting Up Recording	38
6 Default Configuration	40
6.1 Configuring Drives	40
6.2 Configuring Video and Audio Connections	42
6.2.1 General Camera Settings	44
6.2.2 Setting up Dome Cameras and Pan/Tilt Cameras	46
6.2.3 Specifying Monitoring Zone for Motion Cameras	49
6.2.4 Configuring Tamper Detection	50
6.2.5 Configuring Video Monitors	52
6.2.6 Configuring camera sequence	53
6.2.7 Editing Audio Settings	54
6.2.8 Configuring JPEG IP Cameras	55
6.2.9 Configuring MPEG4 IP Cameras	58
6.3 Configuring Recording Settings	60
6.3.1 Configuring Recording Settings for Analog Cameras	60
6.3.2 Configuring Recording Settings of JPEG IP Cameras	67
6.3.3 Configuring Recording Settings of MPEG4 IP Cameras	69
6.4 Configuring Time Periods	71
6.5 Configuring Inputs and Outputs	73
6.5.1 Configuring Alarm Inputs	73
6.5.2 Configuring Relay Outputs	74
6.5.3 Configuring Alarm Simulation	75
6.5.4 Configuring Virtual Inputs	76
6.5.5 Configuring Automatic Teller Machines	77
6.5.6 Configuring Foyer Card Readers	79
6.5.7 Configuring AP Inputs	82
6.5.8 Configuring POS Inputs	86
6.5.9 Configuring ATM/POS Inputs	88
6.6 Configuring Alarm Processing	90
6.7 Configuring Remote Stations	94
6.8 Configuring Alarm Transmission	97
6.9 Configuring the Export Video Scheduler	100
6.10 Creating Authorization Levels	102
6.11 Configuring Users	107
6.12 Configuring Error Forwarding	109
6.13 Configuring Options	111
6.13.1 MIB List for SNMP	114
6.13.2 Notification via SNMP	115
6.13.3 Configuring Automatic Alarm Recording	116
6.14 Configuring Browser Access and Network Settings	117
6.15 Administration and Dongle	119
6.15.1 Activating a License	122
7 Remote configuration	123
8 XP Administration	124
8.1 Logging On as a Windows® XP User	124
8.2 Logging On as a Windows® XP Administrator	124
8.3 Changing the Administrator Password	124
9 Connections	125
9.1 Network Connection via DSL	125
9.2 Connecting the ISDN Controller	128
9.3 Connecting VSCom 200 H (Interface Expansion)	129
9.4 Connecting External Hard Disks	129
9.5 Connecting a Malfunction Relay	129
9.6 Connecting an ATM (Serial)	130
9.7 Connecting the MINITER RS 485 Foyer Card Reader	134
9.8 Connecting the DCF 77 Radio Clock	137
9.9 Connecting a Modem/ISDN Card (for Incoming Connections)	139
9.10 Connecting to AutoDome/SAE Dome	141
9.10.1 Connecting to Bosch Dome Cameras (Directly)	141
9.10.2 Connecting to Bosch Dome Cameras via Matrix Switch	141
9.10.3 Connecting to SAE Dome Cameras (Directly)	142
9.10.4 Connecting to SAE Dome Cameras with V3032 Biphase Interface	142
9.11 Connecting an AP	143
9.11.1 General	143
9.11.2 Connecting to NZ 500 (20 mA) Video System NZ 500	145
9.11.3 Connecting to BZ 500 (20 mA)	145
9.11.4 Connecting to AZ 1010/NZ 1008	146
9.11.5 Connecting to NZ 1012	147
9.11.6 Connecting to NZ 1060	148
9.11.7 Connecting to UEZ 1000 (20 mA)	149
9.11.8 Connecting to UEZ 2000 (20 mA)	149
9.11.9 Connecting to UGM 2020	150
10 Troubleshooting and Checks	151
10.1 Troubleshooting	151
10.2 Checking the Optional Network Connection	152
10.3 Checking the Optional ATM Connection	153
10.4 Checking the Optional Web Connection	154
11 Notes on Service and Maintenance	155
11.1 Maintenance Work to be Carried Out	155
11.2 Software Update	156