Bosch DB18C3100R2 Installation Guide - Page 7

DiBos/DiBos Micro

Safety Notes | en

7

Bosch Sicherheitssysteme GmbH

Installation Guide

F.01U.033.308 | V7 | 2009.09

1

Safety Notes

The following safety notes must be observed:

1.

Read, follow and retain instructions

All safety and operating instructions must be read and followed before installing the

device. Retain instructions for future reference.

2.

Observe warnings

Observe all warnings on the device and in the operating manual.

3.

Add-on devices

Do not use add-on devices that are not recommended by the product manufacturer as

these may cause hazards.

4.

Installation notes

Do not place the device on an unstable mounting, tripod or similar. The device may fall to

the ground and seriously injure the user or be damaged itself. Only use accessories that

have been recommended by the manufacturer or are delivered with the device. Fit the

device according to the manufacturer's instructions. Exercise extreme caution when

transporting the device on a trolley. Abrupt stopping, extreme force effects and uneven

surfaces may cause the device and the trolley to tip over.

5.

Cleaning

Unplug the device from the mains power supply before cleaning. Follow all instructions

for the device. Normally, cleaning can be carried out with a damp cloth. Do not use liquid

cleaners or cleaners in spray cans.

6.

Service

Do not attempt to service the device yourself. You may be exposed to high electrical

voltages or other hazards if you open or remove covers. Servicing must be carried out by

qualified maintenance personnel.

7.

Damage requiring service.

Unplug the device from the mains power supply and arrange for the device to be serviced

by qualified personnel if:

–

The mains cable or mains plug is damaged.

–

Liquids or foreign bodies are present in the device.

–

The device has come into contact with water and/or has been exposed to extreme

environmental conditions (e.g. rain, snow etc.).

–

If the device does not work properly in spite of following the operating instructions,

make changes only to those operating elements that are described in the operating

instructions. Incorrect changes to other operating elements may cause damage

requiring extensive repair work to be carried out by qualified service personnel.

–

The device has fallen to the ground or the housing has been damaged.

–

A noticeable change in the performance of the device has occurred. In this case, the

device must be serviced.

8.

Spare parts

If spare parts are required, service personnel must use spare parts that are

recommended by the manufacturer or correspond to the original parts. Using the wrong

spare parts may result in fire, electric shock or other hazards.

9.

Safety test

When servicing or repair is complete, ask service personnel to carry out a safety test to

ensure that the device is working correctly.

Section	Page
1 Safety Notes	7
2 Introduction	11
2.1 System Description	11
2.2 Unpacking	11
2.3 Power	11
2.4 Environmental	11
2.5 Recommended Virus Scanners/Firewall	12
2.5.1 Virus Scanners	12
2.5.2 Firewall	12
2.6 System Overview/Technical Specifications	14
2.6.1 DiBos	14
2.6.2 DiBos micro	18
3 Device Connections	21
3.1 DiBos	21
3.1.1 DiBos Front View	21
3.1.2 DiBos Rear View	22
3.1.3 Grabber Card for DiBos	23
3.1.4 I/O Card for DiBos	24
3.2 DiBos micro	25
3.2.1 DiBos micro Front View	25
3.2.2 DiBos micro Rear View	26
3.2.3 Grabber Card for DiBos micro	27
3.2.4 I/O Card (for DiBos micro)	28
4 Quick Installation	30
5 Quick Configuration	31
5.1 General Settings	31
5.2 Creating a User	33
5.3 Setting up the Network	34
5.4 Specifying Cameras	36
5.5 Assigning Time Profiles	37
5.6 Setting Up Recording	38
6 Default Configuration	40
6.1 Configuring Drives	40
6.2 Configuring Video and Audio Connections	42
6.2.1 General Camera Settings	44
6.2.2 Setting up Dome Cameras and Pan/Tilt Cameras	46
6.2.3 Specifying Monitoring Zone for Motion Cameras	49
6.2.4 Configuring Tamper Detection	50
6.2.5 Configuring Video Monitors	52
6.2.6 Configuring camera sequence	53
6.2.7 Editing Audio Settings	54
6.2.8 Configuring JPEG IP Cameras	55
6.2.9 Configuring MPEG4 IP Cameras	58
6.3 Configuring Recording Settings	60
6.3.1 Configuring Recording Settings for Analog Cameras	60
6.3.2 Configuring Recording Settings of JPEG IP Cameras	67
6.3.3 Configuring Recording Settings of MPEG4 IP Cameras	69
6.4 Configuring Time Periods	71
6.5 Configuring Inputs and Outputs	73
6.5.1 Configuring Alarm Inputs	73
6.5.2 Configuring Relay Outputs	74
6.5.3 Configuring Alarm Simulation	75
6.5.4 Configuring Virtual Inputs	76
6.5.5 Configuring Automatic Teller Machines	77
6.5.6 Configuring Foyer Card Readers	79
6.5.7 Configuring AP Inputs	82
6.5.8 Configuring POS Inputs	86
6.5.9 Configuring ATM/POS Inputs	88
6.6 Configuring Alarm Processing	90
6.7 Configuring Remote Stations	94
6.8 Configuring Alarm Transmission	97
6.9 Configuring the Export Video Scheduler	100
6.10 Creating Authorization Levels	102
6.11 Configuring Users	107
6.12 Configuring Error Forwarding	109
6.13 Configuring Options	111
6.13.1 MIB List for SNMP	114
6.13.2 Notification via SNMP	115
6.13.3 Configuring Automatic Alarm Recording	116
6.14 Configuring Browser Access and Network Settings	117
6.15 Administration and Dongle	119
6.15.1 Activating a License	122
7 Remote configuration	123
8 XP Administration	124
8.1 Logging On as a Windows® XP User	124
8.2 Logging On as a Windows® XP Administrator	124
8.3 Changing the Administrator Password	124
9 Connections	125
9.1 Network Connection via DSL	125
9.2 Connecting the ISDN Controller	128
9.3 Connecting VSCom 200 H (Interface Expansion)	129
9.4 Connecting External Hard Disks	129
9.5 Connecting a Malfunction Relay	129
9.6 Connecting an ATM (Serial)	130
9.7 Connecting the MINITER RS 485 Foyer Card Reader	134
9.8 Connecting the DCF 77 Radio Clock	137
9.9 Connecting a Modem/ISDN Card (for Incoming Connections)	139
9.10 Connecting to AutoDome/SAE Dome	141
9.10.1 Connecting to Bosch Dome Cameras (Directly)	141
9.10.2 Connecting to Bosch Dome Cameras via Matrix Switch	141
9.10.3 Connecting to SAE Dome Cameras (Directly)	142
9.10.4 Connecting to SAE Dome Cameras with V3032 Biphase Interface	142
9.11 Connecting an AP	143
9.11.1 General	143
9.11.2 Connecting to NZ 500 (20 mA) Video System NZ 500	145
9.11.3 Connecting to BZ 500 (20 mA)	145
9.11.4 Connecting to AZ 1010/NZ 1008	146
9.11.5 Connecting to NZ 1012	147
9.11.6 Connecting to NZ 1060	148
9.11.7 Connecting to UEZ 1000 (20 mA)	149
9.11.8 Connecting to UEZ 2000 (20 mA)	149
9.11.9 Connecting to UGM 2020	150
10 Troubleshooting and Checks	151
10.1 Troubleshooting	151
10.2 Checking the Optional Network Connection	152
10.3 Checking the Optional ATM Connection	153
10.4 Checking the Optional Web Connection	154
11 Notes on Service and Maintenance	155
11.1 Maintenance Work to be Carried Out	155
11.2 Software Update	156

Bosch DB18C3100R2 Installation Guide - Page 7

Safety Notes, Observe warnings - manual

Page 7 highlights