Bosch SHV78B73UC Use and Care Manuals - Page 54

Issue, Cause and troubleshooting, Reset

Get Bosch SHV78B73UC PDF manuals and user guides View all Bosch SHV78B73UC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

en-us Troubleshooting Issue UP appears on the display. Cause and troubleshooting A software update is available. ▶ Press the remote start button to install the soft- ware update. a After a successful software update, "Suc" appears on the display for a few seconds. Water is left in the Filter system or area under the filters is blocked. appliance at the end 1. Clean the Filters → Page 40. of the program. 2. Clean the Drain pump → Page 56. Program has not yet ended. ▶ Wait until the program ends or terminate the program with Reset. ▶ → "Terminating the wash cycle", Page 32 Appliance cannot be Software update is taking place. switched on or oper- ▶ Wait until the software update has finished. ated. Appliance functions have failed. 1. Pull out the power cord plug or switch off the breaker. 2. Wait at least 2 minutes. 3. Connect the appliance to the power supply. 4. Switch the appliance on. Appliance does not The breaker has tripped. start. ▶ Check the relevant breaker. Power cord is not inserted. 1. Check whether the power outlet is working. 2. Check whether the power cord plug is properly inserted in the power outlet and on the rear of the appliance. Appliance door is not closed properly. ▶ Close the appliance door. Wash cycle starts You did not wait until the cycle ended. up automatically. ▶ → "Terminating the wash cycle", Page 32 Appliance stops dur- Appliance door is not closed properly. ing the cycle or cuts ▶ Close the appliance door. out. Power and/or water supply has been interrupted. 1. Check the power supply. 2. Check the water supply. Upper rack is pressing against inner door and preventing appliance door from being closed securely. 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
en-us
Troubleshooting
54
Issue
Cause and troubleshooting
UP appears on the
display.
A software update is available.
▶
Press the remote start button to install the soft-
ware update.
a
After a successful software update, "Suc" ap-
pears on the display for a few seconds.
Water is left in the
appliance at the end
of the program.
Filter system or area under the filters is blocked.
1.
Clean the Filters
→
Page 40
.
2.
Clean the Drain pump
→
Page 56
.
Program has not yet ended.
▶
Wait until the program ends or terminate the
program with
Reset
.
▶
→
"Terminating the wash cycle", Page 32
Appliance cannot be
switched on or oper-
ated.
Software update is taking place.
▶
Wait until the software update has finished.
Appliance functions have failed.
1.
Pull out the power cord plug or switch off the
breaker.
2.
Wait at least 2 minutes.
3.
Connect the appliance to the power supply.
4.
Switch the appliance on.
Appliance does not
start.
The breaker has tripped.
▶
Check the relevant breaker.
Power cord is not inserted.
1.
Check whether the power outlet is working.
2.
Check whether the power cord plug is properly
inserted in the power outlet and on the rear of
the appliance.
Appliance door is not closed properly.
▶
Close the appliance door.
Wash cycle starts
up automatically.
You did not wait until the cycle ended.
▶
→
"Terminating the wash cycle", Page 32
Appliance stops dur-
ing the cycle or cuts
out.
Appliance door is not closed properly.
▶
Close the appliance door.
Power and/or water supply has been interrupted.
1.
Check the power supply.
2.
Check the water supply.
Upper rack is pressing against inner door and
preventing appliance door from being closed se-
curely.