Bosch WTMC8521UC Installation and Use & Care (all languages) - Page 10
Attention
UPC - 825225852322
View all Bosch WTMC8521UC manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
Mobile home kit part no. WTZ 1275 Note: Please check with the Authority Having Jurisdiction in your area to verify if a gas dryer can be installed in your mobile home. Once that has been verified, installation of the dryer shall conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 {formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280)}, and/or Standard CAN/CSAĆZ240 MH. Please use mobile home kit number WTZ 1275 for means to secure the dryer to the structure. See page 9 Exhaust Air Connection" for the exhaust duct installation instructions. The exhaust duct must be securely fastened to a noncombustible portion of the mobile home structure and must not terminate beneath the mobile home. An opening to the outside must be provided during installation. Insure that the free area of the opening for the introduction of outside air is not less than twice the area of the dryer exhaust outlet or use at least a 5 inch diameter exhaust or at least a 25 in2 square exhaust duct for the opening. Installation ć step by step 1. Unpack the dryer. 2. Remove all objects from the drum. 3. Check the dryer for visible damage. 4. Position the dryer near the installation location. 5. If required, have customer service change the door hinges to the left (see page 6). 6. If required, have customer service install the exhaust air outlet on the dryer (see page 8). 7. Have the gas supply connected by an qualified technician (see page 7). 8. Install exhaust duct, if necessary. Follow the installation instructions supplied by the appropriate manufacturer! i If space is very restricted, it is recommended to fit the initial parts of the exhaust duct to the dryer before the dryer is moved to its final installation location. 9. Move the dryer to its final location and align. ATTENTION Do not slide dryer across the floor if heightĆadjustable feet have been extended. Feet and/or dryer base may be damaged if dryer is slid across floor with heightĆadjustable feet extended. 10. Position and then level the dryer. The dryer should be level with all four feet firmly on the ground. The dryer must not wobble. If the dryer is not level or if it does wobble, the feet must be adjusted. Adjust the heightĆadjustable feet until the dryer does not rock and is level, both frontĆtoĆback and sideĆtoĆside. 11. Connect the exhaust duct to the exhaust air outlet on the dryer. 12. Insert plug into the wall receptacle. Check list before using the dryer 1. Check that steps 1-12 have been implemented properly. 2. Ensure that the dryer is connected to the power supply. 3. Open the shutoffĆvalve. 4. Read the operating instructions to understand how your dryer operates. 5. Conduct an appliance test: q Check that the drum is empty. q Close the dryer door. q Switch the dryer to Extra Dry" and then press the Start button. q After 3-5 minutes press the Stop button and open the door. 6. If the interior of the dryer feels warm, the dryer has been connected properly. Switch the dryer to Off". 7. If the dryer does not work, switch the dryer to Off". Look in the troubleshooting section (page 22) of the OPERATING INSTRUCTIONS and find the fault. Preparing to transport the dryer ć step by step 1. Close the shutĆoff valve. 2. Rotate the program selector to OFF". 3. Pull out the power supply plug or turn off the circuit breaker. 4. Disconnect gas supply 5. Disconnect the exhaust duct from the exhaust air outlet on the dryer. 6. Place any accessories in the drum. 7. Close the door and secure with adhesive tape. 8. Screw the heightĆadjustable feet of the dryer into the housing to prevent them from being damaged during transportation. 10