Bose Virtually Invisible 191 Installation Guide - Page 6
English, Français, Nederlands, Deutsch, Italiano - speakers white
View all Bose Virtually Invisible 191 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 6 highlights
Nederlands Italiano Français Deutsch English PREPARATION Deciding on speaker placement The design of your new Virtually Invisible® 191 speakers makes them well-suited to either wall or ceiling installation. The location you choose will affect the procedure for installing them. Consider the options below, then follow the instructions that apply to your choices: • How you will use the speakers? • for stereo sound at the front of a room or seating arrangement, or • as home theater front speakers or surround sound rear speakers • What surface will you install them in? • an interior wall (abutting another room), or exterior wall (abutting outside), or ceiling • in finished (plaster and lath or wallboard), or new construction Figure 4 Template Three tips for determining speaker placement 1. The template can be placed against a wall or ceiling to help determine the amount of space the speaker will need. Each speaker enclosure extends into the wall or ceiling, as shown in the gray DO NOT CUT area on the template (Figure 4). In a wall, the speaker may be inserted either up or down and will extend either above or below the grille. 2. Use of a stud finder can help ensure that the speaker hole is at least 43/4 in. (12 cm) from a stud or joist. 3. All electrical wiring, vents and plumbing pipes located inside the walls must be avoided (Figure 5 on page 7). Check with a trained professional to learn how to locate and avoid them. Note: To prevent problems with condensation in cold climates where a humidifier is used, avoid inserting the speaker upside-down in an exterior wall. TAPE HERE WARNING: Make sure the spot chosen is safe for cutting. Do not cut through surfaces that have hazards, such as electrical wiring, conduits or plumbing, concealed behind them. If you are not sure, consult a professional installer before you proceed. TAPE HERE 8 1/16" (20.5 cm) Translations below WARNING: Make sure the spot chosen is safe for cutting. Do not cut through surfaces that have hazards, such as electrical wiring, conduits or plumbing, concealed behind them. If you are not sure, consult a professional installer before you proceed. WARNING: Make sure the spot chosen is safe for drilling. Do not cut through surfaces that have hazards concealed behind them, such as electrical wiring, conduits or plumbing. If you are not sure, consult a professional installer before you proceed. WARNING: Make sure the spot chosen is safe for drilling. Do not cut through surfaces that have hazards concealed behind them, such as electrical wiring, conduits or plumbing. If you are not sure, consult a professional installer before you proceed. WHITE CUT OUT AREA WHITE CUT OUT AREA 5 1/2" (14 cm) WARNING: Make sure the spot chosen is safe for drilling. Do not cut through surfaces that have hazards concealed behind them, such as electrical wiring, conduits or plumbing. If you are not sure, consult a professional installer before you proceed. WARNING: Make sure the spot chosen is safe for drilling. Do not cut through surfaces that have hazards concealed behind them, such as electrical wiring, conduits or plumbing. If you are not sure, consult a professional installer before you proceed. Pilot Hole WARNING: Make sure the spot chosen is safe for drilling. Do not cut through surfaces that have hazards concealed behind them, such as electrical wiring, conduits or plumbing. If you are not sure, consult a professional installer before you proceed. WARNING: Make sure the spot chosen is safe for drilling. Do not cut through surfaces that have hazards concealed behind them, such as electrical wiring, conduits or plumbing. If you are not sure, consult a professional installer before you proceed. TAPE HERE DO NOT CUT AROUND GRAY AREA English & Translations 141/2" (36.9 cm) 9" (22.9 cm) DO NOT CUT AROUND GRAY AREA DO NOT CUT AROUND TAPE HERE GRAY AREA DO NOT CUT AROUND GRAY AREA DO NOT CUT AROUND GRAY AREA DO NOT CUT AROUND GRAY AREA FOR CUTTING Large white area represents what to cut out for the speaker face. NOT FOR CUTTING Large gray area represents space to reserve behind the wall for the speaker enclosure. DO NOT TAPE CUT AROUND HERE GRAY AREA DO NOT CUT AROUND TAPE GRAY AREA HERE 6