Brother International BAS-310 Instruction Manual - English - Page 14

Brother International BAS-310 Manual

Get Brother International BAS-310 PDF manuals and user guides View all Brother International BAS-310 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

El Using the TEST switch GO° 0 TEST STEP BACK U / 0 * Use the TEST switch to begin sewing again from any desired point when the thread breaks or the bobbin thread runs out. (1) Press the emergency stop switch 0 while the sewing machine is running. (All operations will stop, and an alarm will sound.) (2) Press the emergency stop switch 0 again. (The thread cutter will operate and the alarm will stop.) (3) Press the starting pedal 0. The work clamp will move automatically to the sewing start position. (4) Press the TEST switch 0. The test indicator 0 will light. (5) Press the starting pedal 0. (The needle will remain sationary as the work clamp advances through the pattern at low speed one stitch at a time. Press the presser lifter pedal 0 to fast forward.) (6) When the work clamp reaches the desired position, press the TEST switch 0 twice. The work clamp will stop, and the test indicator 0 will go out. If the work clamp was stopped too early, press the TEST switch 0 again to proceed. (7) Sewing will start when the start switch 0 is pressed. The work clamp can be forwarded in 100 stitch units by pressing the STEP BACK switch 0 when the TEST switch 0 is on. Also, pressing the STEP BACK switch after the TEST switch 0 is turned off will advance the work clamp one stitch at a time. (Press the presser lifter pedal 0 to fast forward.) E] Using the emergency stop switch * Press the emergency stop switch to immediately stop the sewing machine during actual sewing or when in the test mode. (1) If the emergency stop switch 0 is pressed while sewing. All operations will stop, and an alarm will sound. Correct the problem, and press the emergency stop switch 0 again. The thread cutter will operate, the emergency stop function will be cancelled, and the alarm will stop. 0 There will be no response when either foot switch is pressed when the emergency stop switch O --is 0 on (the alarm is sounding). (2) If the emergency stop switch 0 is pressed during the test mode. All operations will stop, and an alarm will sound. The emergency stop function will be cancelled when the emergency stop switch 0 is pressed. (3) If a problem occurs If an abnormal load is applied or a problem occurs during sewing, the emergency stop function is automatically activated, all operations stop, and the alarm sounds. Press the emergency stop switch 0 to cancel the emergency stop mode. -11-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
El
Using
the
TEST
switch
GO°
TEST
U
/
0
STEP
BACK
E]
Using
the
emergency
stop
switch
0
(3)
*
Use
the
TEST
switch
to
begin
sewing
again
from
any
desired
point
when
the
thread
breaks
or
the
bobbin
thread
runs
out.
(1)
Press
the
emergency
stop
switch
0
while
the
sewing
machine
is
running.
(All
operations
will
stop,
and
an
alarm
will
sound.)
(2)
Press
the
emergency
stop
switch
0
again.
(The
thread
cutter
will
operate
and
the
alarm
will
stop.)
(3)
Press
the
starting
pedal
0.
The
work
clamp
will
move
automatically
to
the
sewing
start
position.
(4)
Press
the
TEST
switch
0.
The
test
indicator
0
will
light.
(5)
Press
the
starting
pedal
0.
(The
needle
will
remain
sationary
as
the
work
clamp
advances
through
the
pattern
at
low
speed
one
stitch
at
a
time.
Press
the
presser
lifter
pedal
0
to
fast
forward.)
(6)
When
the
work
clamp
reaches
the
desired
position,
press
the
TEST
switch
0
twice.
The
work
clamp
will
stop,
and
the
test
indicator
0
will
go
out.
If
the
work
clamp
was
stopped
too
early,
press
the
TEST
switch
0
again
to
proceed.
(7)
Sewing
will
start
when
the
start
switch
0
is
pressed.
The
work
clamp
can
be
forwarded
in
100
stitch
units
by
pressing
the
STEP
BACK
switch
0
when
the
TEST
switch
0
is
on.
Also,
pressing
the
STEP
BACK
switch
after
the
TEST
switch
0
is
turned
off
will
advance
the
work
clamp
one
stitch
at
a
time.
(Press
the
presser
lifter
pedal
0
to
fast
forward.)
*
Press
the
emergency
stop
switch
to
immediately
stop
the
sewing
machine
during
actual
sewing
or
when
in
the
test
mode.
(1)
If
the
emergency
stop
switch
0
is
pressed
while
sewing.
All
operations
will
stop,
and
an
alarm
will
sound.
Correct
the
problem,
and
press
the
emergency
stop
switch
0
again.
The
thread
cutter
will
operate,
the
emergency
stop
function
will
be
cancelled,
and
the
alarm
will
stop.
0
There
will
be
no
response
when
either
foot
switch
is
pressed
when
the
emergency
stop
switch
O
--
is
on
(the
alarm
is
sounding).
(2)
If
the
emergency
stop
switch
0
is
pressed
during
the
test
mode.
All
operations
will
stop,
and
an
alarm
will
sound.
The
emergency
stop
function
will
be
cancelled
when
the
emergency
stop
switch
0
is
pressed.
If
a
problem
occurs
If
an
abnormal
load
is
applied
or
a
problem
occurs
during
sewing,
the
emergency
stop
function
is
automatically
activated,
all
operations
stop,
and
the
alarm
sounds.
Press
the
emergency
stop
switch
0
to
cancel
the
emergency
stop
mode.
—11—