Brother International HL 5170DN Network Users Manual - English - Page 107

TCP/IP CONFIGURATION, using the SET IP ADDRESS command the printer's control - reset

Get Brother International HL 5170DN - B/W Laser Printer PDF manuals and user guides
UPC - 012502612667
View all Brother International HL 5170DN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 107 highlights

T You must be on the same Ethernet segment (that is, there cannot be a router between the print server and operating system) to use the arp -s command. If there is a router, you may use BOOTP or other methods described in this chapter to enter the IP address. If your Administrator has configured the system to deliver IP addresses using BOOTP, DHCP or RARP your Brother print server can receive an IP address from any one of these IP address allocation systems. In which case, you will not need to use the ARP command. The ARP command only works once. For security reasons, once you have successfully configured the IP address of a Brother print server using the ARP command, you cannot use the ARP command again to change the address. The print server will ignore any attempts to do this. If you wish to change the IP address again, use a Web Browser, TELNET (using the SET IP ADDRESS command) the printer's control panel (if applicable) or factory reset the print server (which will then allow you to use the ARP command again). To configure the print server and to verify the connection, enter the following command ping ipaddress where ipaddress is the IP address of the print server. For example, ping 192.189.207.2. 10 - 7 TCP/IP CONFIGURATION

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
10 - 7 TCP/IP CONFIGURATION
T
You must be on the same Ethernet segment (that is, there cannot
be a router between the print server and operating system) to use
the arp -s command.
If there is a router, you may use BOOTP or other methods
described in this chapter to enter the IP address.
If your Administrator has configured the system to deliver IP
addresses using BOOTP, DHCP or RARP your Brother print
server can receive an IP address from any one of these IP
address allocation systems. In which case, you will not need to
use the ARP command. The ARP command only works once. For
security reasons, once you have successfully configured the IP
address of a Brother print server using the ARP command, you
cannot use the ARP command again to change the address. The
print server will ignore any attempts to do this. If you wish to
change the IP address again, use a Web Browser, TELNET
(using the SET IP ADDRESS command) the printer’s control
panel
(if applicable)
or factory reset the print server (which will
then allow you to use the ARP command again).
To configure the print server and to verify the connection,
enter the following command
ping ipaddress
where
ipaddress
is the IP address of the print server. For
example,
ping 192.189.207.2
.