Brother International MFC-9010CN Users Manual - English - Page 74

Stop/Exit, Black Start, Color Start, Error Message, Cause, Action, Cooling Down, Wait for a while

Get Brother International MFC-9010CN - Color LED - All-in-One PDF manuals and user guides
UPC - 012502622383
View all Brother International MFC-9010CN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Error Message Cause Action Cooling Down Wait for a while The temperature of the drum unit or toner cartridge is too hot. The machine will pause its current print job and go into cooling down mode. During the cooling down mode, you will hear the cooling fan running while the LCD shows Cooling Down, and Wait for a while. Make sure that you can hear the fan in the machine spinning and that the exhaust outlet is not blocked by something. If the fan is spinning, remove any obstacles that surround the exhaust outlet, and then leave the machine turned on but do not use it for several minutes. If the fan is not spinning, disconnect the machine from the power for several minutes, then reconnect it. Cover is Open The ADF cover is not closed completely. Close the ADF cover of the machine, then press Stop/Exit. The top cover is not closed completely. Close the top cover of the machine. Cover is Open The fuser cover is not closed completely or paper was jammed in the back of the machine when you turned on the power. „ Close the fuser cover of the machine. „ Make sure paper is not jammed inside the back of the machine, and then close the fuser cover and press Black Start or Color Start. DIMM Error The DIMM is not installed correctly. Or the DIMM is broken. Turn off the machine. Re-install the DIMM correctly. Wait a few seconds, and then turn it on again. If this error message appears again, replace the DIMM with a new one. (See Installing extra memory on page 47.) Document Jam The document was not inserted or fed properly, or the document scanned from the ADF was too long. See Document jams on page 66 or Using the automatic document feeder (ADF) on page 20. Drum Error The corona wire on the drum unit Clean the corona wire on the drum unit. (See needs to be cleaned. Cleaning the corona wires on page 75.) It is time to replace the drum units. Replace the drum unit with a new one for the color that is indicated on the LCD. (See Replacing the drum units on page 93.) Drums End Soon The drum unit is near the end of Buy new drum units before you get a its life. Replace Drums message. Drum End Soon(X) 1 The drum unit for the color indicated on the LCD is near the end of its life. Buy new drum unit for the color indicated on the LCD before you get a Replace Drum(X) 1 message. Fuser Error The temperature of fuser unit Turn the power switch off, wait a few does not rise at a specified seconds, and then turn it on again. Leave the temperature within specified time. machine for 15 minutes with the power on. The fuser unit is too hot. 62

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
62
Cooling Down
Wait for a while
The temperature of the drum unit
or toner cartridge is too hot. The
machine will pause its current
print job and go into cooling down
mode. During the cooling down
mode, you will hear the cooling
fan running while the LCD shows
Cooling Down
, and
Wait for a while.
Make sure that you can hear the fan in the
machine spinning and that the exhaust outlet
is not blocked by something.
If the fan is spinning, remove any obstacles
that surround the exhaust outlet, and then
leave the machine turned on but do not use
it for several minutes.
If the fan is not spinning, disconnect the
machine from the power for several minutes,
then reconnect it.
Cover is Open
The ADF cover is not closed
completely.
Close the ADF cover of the machine, then
press
Stop/Exit
.
The top cover is not closed
completely.
Close the top cover of the machine.
Cover is Open
The fuser cover is not closed
completely or paper was jammed
in the back of the machine when
you turned on the power.
Close the fuser cover of the machine.
Make sure paper is not jammed inside
the back of the machine, and then close
the fuser cover and press
Black Start
or
Color Start
.
DIMM Error
The DIMM is not installed
correctly. Or the DIMM is broken.
Turn off the machine. Re-install the DIMM
correctly. Wait a few seconds, and then turn
it on again. If this error message appears
again, replace the DIMM with a new one.
(See
Installing extra memory
on page 47.)
Document Jam
The document was not inserted
or fed properly, or the document
scanned from the ADF was too
long.
See
Document jams
on
page
66 or
Using the
automatic document feeder (ADF)
on page 20.
Drum Error
The corona wire on the drum unit
needs to be cleaned.
Clean the corona wire on the drum unit. (See
Cleaning the corona wires
on page 75.)
It is time to replace the drum
units.
Replace the drum unit with a new one for the
color that is indicated on the LCD. (See
Replacing the drum units
on page 93.)
Drums End Soon
The drum unit is near the end of
its life.
Buy new drum units before you get a
Replace Drums
message.
Drum End Soon(X)
1
The drum unit
for the color
indicated on the LCD is near the
end of its life.
Buy new drum unit for the color indicated on
the LCD before you get a
Replace Drum(X)
1
message.
Fuser Error
The temperature of fuser unit
does not rise at a specified
temperature within specified time.
Turn the power switch off, wait a few
seconds, and then turn it on again. Leave the
machine for 15 minutes with the power on.
The fuser unit is too hot.
Error Message
Cause
Action