Brother International PS 9000 User Manual - Page 45

PS-9000 Settings, Factory, Default, Explanation, CD-ROM, Setup, Web

Get Brother International PS 9000 - Print Server - USB PDF manuals and user guides
UPC - 012502607786
View all Brother International PS 9000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

PS-9000 Settings Below are the settings for PS-9000. General Name CD-ROM Setup Web page Factory Default LAN Interface AUTO TCP/IP Name CD-ROM Setup Web page Factory Default Receive IP address DHCP/BOOTP automatically ENABLE RARP ENABLE IP Address IP Address 0.0.0.0 Explanation Set up network type. Normally use in AUTO. If the LINK LED on the hub does not light up after the PS-9000 is turned on, select the appropriate network type for the hub. Explanation Enables or disables DHCP/BOOTP. These are protocols where the IP address is acquired from the DHCP/BOOTP server during start up. In order for DHCP/BOOTP to specify the IP address of PS-9000, a DHCP/BOOTP server must exist within the subnetwork and be properly set up. PS-9000 will automatically acknowledge DHCP and BOOTP, and use as its own address the IP address that it previously received as a reply. Enables or disables RARP. RARP is a protocol where the IP address is acquired from the RARP server during start up. In order for DHCP/BOOTP to specify the IP address of PS-9000, an RARP server must exist within the subnetwork and be properly set up. Sets up the IP address of PS-9000. The value must be configured in the format of four series of numbers separated by decimal points, such as "xxx.xxx.xxx.xxx". 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
44
PS-9000 Settings
Below are the settings for PS-9000.
General
TCP/IP
Name
Factory
Default
Explanation
CD-ROM
Setup
Web page
LAN Interface
AUTO
Set up network type. Normally use in
AUTO. If the LINK LED on the hub
does not light up after the PS-9000 is
turned on, select the appropriate
network type for the hub.
Name
Factory
Default
Explanation
CD-ROM
Setup
Web page
Receive IP
address
automatically
DHCP/BOOTP
ENABLE
Enables or disables DHCP/BOOTP.
These are protocols where the IP
address is acquired from the
DHCP/BOOTP server during start up.
In order for DHCP/BOOTP to specify
the IP address of PS-9000, a
DHCP/BOOTP server must exist
within the subnetwork and be
properly set up. PS-9000 will
automatically acknowledge DHCP
and BOOTP, and use as its own
address the IP address that it
previously received as a reply.
RARP
ENABLE
Enables or disables RARP. RARP is a
protocol where the IP address is
acquired from the RARP server during
start up. In order for DHCP/BOOTP to
specify the IP address of PS-9000, an
RARP server must exist within the
subnetwork and be properly set up.
IP Address
IP Address
0.0.0.0
Sets up the IP address of PS-9000. The
value must be configured in the
format of four series of numbers
separated by decimal points, such as
“xxx.xxx.xxx.xxx”.