Canon REALiS WUX6000 Pro AV User Manual
Canon REALiS WUX6000 Pro AV Manual
 |
View all Canon REALiS WUX6000 Pro AV manuals
Add to My Manuals
Save this manual to your list of manuals |
Canon REALiS WUX6000 Pro AV manual content summary:
- Canon REALiS WUX6000 Pro AV | User Manual - Page 1
MULTIMEDIA PROJECTOR User's Manual Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Other Information - Canon REALiS WUX6000 Pro AV | User Manual - Page 2
digital image on a large screen. This Manual This is the user's manual for WUX6000 Multimedia Projectors. The "Operation" section describes how to use the projector. The "Installation and Maintenance" section describes the projector installation procedure, network connection procedure, and regular - Canon REALiS WUX6000 Pro AV | User Manual - Page 3
How to Use This Manual Copyright Notice Please note that enlarging or reducing the size of an image for commercial purposes or public presentation may infringe on the legally protected - Canon REALiS WUX6000 Pro AV | User Manual - Page 4
Projector Highlights High-Resolution LCOS Projection Projection at 1920x1200 (WUXGA), thanks to high-resolution reflective liquid crystal on silicon (LCOS) panels. Lens Shift Lens shift enables motorized image repositioning up, down, left, or right (P46) for greater freedom in installation manual. 4 - Canon REALiS WUX6000 Pro AV | User Manual - Page 5
Quick Reference Guide This Quick Reference Guide will help you find functions that make full use of the projector and are useful for producing an attractive presentation, etc. Connecting the Projector Connecting to the Computer (P132 - P134) Connecting to AV Equipment (P135 - P137) Projecting an - Canon REALiS WUX6000 Pro AV | User Manual - Page 6
to Use This Manual 2 Projector Highlights 4 Quick Reference Guide 5 Safety Instructions 10 Safety Precautions 11 CAUTION ON HANGING FROM THE CEILING 11 AC Power Cord Requirement 14 Federal Communication Commission Notice 15 Precautions for Use 17 Precautions for Installation 18 Precautions - Canon REALiS WUX6000 Pro AV | User Manual - Page 7
Setting ....... 111 Checking Projector Information 112 Installation and Maintenance Installation 113 Before Installation 114 Precautions When Carrying/ Shipping the Projector 114 Precautions for Installation 114 Installation Procedure 118 Setting Up the Projector 118 Installing / Removing the - Canon REALiS WUX6000 Pro AV | User Manual - Page 8
AV Equipment 135 Plugging the Projector In 138 Starting Projection 139 Starting and Stopping Projection..... 139 Changing Notebook Computer Screen Output 140 Installation-Related Menu Settings 141 Locking Installation Position 149 Showing/Hiding the Guide Screen ... 149 Showing/Hiding Input - Canon REALiS WUX6000 Pro AV | User Manual - Page 9
Table of Contents Relationship between Aspect and Screen Aspect 209 Displayed Test Patterns 213 Supported Signal Types........... 214 Product Specifications 216 Index 224 Option 227 Menu Configuration 228 Table of Contents 9 - Canon REALiS WUX6000 Pro AV | User Manual - Page 10
accidents. If your projector does not seem to be operating properly, read this manual again, check operations and cable connections, and try the solutions in the "Troubleshooting" section in the back of this manual. If the problem still persists, contact the Canon Customer Support Center. CAUTION - Canon REALiS WUX6000 Pro AV | User Manual - Page 11
that children do not stare directly into the beam. • Install the projector in a proper position. Otherwise it may result in a projector. Heat build-up can reduce the service life of your projector, and can also be dangerous. • If the projector is unused for an extended time, unplug the projector - Canon REALiS WUX6000 Pro AV | User Manual - Page 12
■ READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE. All the safety and operating instructions should be read before beginning to operate the product. Read all of the instructions given here and retain them for later use. Unplug this projector from the AC power supply before cleaning. Do not - Canon REALiS WUX6000 Pro AV | User Manual - Page 13
Instructions Safety Instructions Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind onto the projector. Do not install the projector - Canon REALiS WUX6000 Pro AV | User Manual - Page 14
Instructions AC Power Cord Requirement The AC Power Cord supplied with this projector contact your electrician. Ground THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE. NOTE FOR CUSTOMERS household waste disposal service or visit www.canon-europe.com/weee, or www - Canon REALiS WUX6000 Pro AV | User Manual - Page 15
Safety Instructions Safety Instructions Federal Communication Commission Notice Multimedia Projector, Model: WUX6000 This device complies with Part installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions - Canon REALiS WUX6000 Pro AV | User Manual - Page 16
Safety Instructions Safety Symbols in this Manual This section describes the safety symbols used in this manual. Important projector safety information is identified by the following symbols. Always observe the safety information by these symbols. Denotes the risk of death or serious injury from - Canon REALiS WUX6000 Pro AV | User Manual - Page 17
Instructions Safety Instructions Precautions for Use As this section contains important safety-related information, be sure to read the following carefully beforehand in order to use your projector contact the Canon Customer Support Center. • The power cord included with this projector is for use - Canon REALiS WUX6000 Pro AV | User Manual - Page 18
Safety Instructions Pay attention to the following points regarding the power source or dirt from between the plug and the outlet. Precautions for Installation Pay attention to the following points regarding installation and handling of the projector. Failure to do so may cause a fire, electric shock - Canon REALiS WUX6000 Pro AV | User Manual - Page 19
Instructions Safety Instructions Pay attention to the following points regarding installation and handling of the projector. Failure to do so may cause a fire, electric shock or personal injury. • Do not move the projector Customer Support Center. • Do not disassemble or modify the projector ( - Canon REALiS WUX6000 Pro AV | User Manual - Page 20
Safety Instructions Pay attention to the following points regarding installation and handling of the projector. • If the projector will projector be performed. For details of maintenance costs, contact the Canon Customer Support Center. • When hanging the projector from a ceiling, put the projector - Canon REALiS WUX6000 Pro AV | User Manual - Page 21
Safety Instructions Safety Instructions Precautions on the lamp This projector uses a high-pressure mercury lamp attempt to replace the lamp by yourself. Always request service from the Canon Customer Support Center. Additionally, with ceiling-mounted projectors, the lamp may fall out when you open - Canon REALiS WUX6000 Pro AV | User Manual - Page 22
to cool down sufficiently. Failure to do so could result in a burn or personal injury due to heat from the lamp or projector. • When an instruction to replace the lamp has been displayed (LAMP Indicator Displays (P35)), the possibility of the lamp breaking will increase. Replace the lamp with - Canon REALiS WUX6000 Pro AV | User Manual - Page 23
damaged. Removal and installation of the lens unit should not be performed by the user. Be sure to have the procedure performed by a qualified technician or contact the Canon Customer Support Center. • Disconnect the cables connected to the projector. Carrying the projector with the cables attached - Canon REALiS WUX6000 Pro AV | User Manual - Page 24
the air intake and exhaust vents are separated from the wall by more than 50 cm (1.6'). Failure to do so could cause a malfunction. • Do not install the projector in a location that is damp, or where there is a lot of dust, oily smoke or tobacco smoke. Doing so could cause contamination of optical - Canon REALiS WUX6000 Pro AV | User Manual - Page 25
PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NO SUPPORT Canon Inc., and all its subsidiaries or its dealers do not make any support service regarding the source code. Canon Inc., and all its subsidiaries or its dealers shall not respond to any - Canon REALiS WUX6000 Pro AV | User Manual - Page 26
26 - Canon REALiS WUX6000 Pro AV | User Manual - Page 27
Before Use Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Other Information Index 27 - Canon REALiS WUX6000 Pro AV | User Manual - Page 28
supported with this projector. The RS-RC05 can also be used as a wired remote. (P30) • Computer cable (1.8 m / 5.9') (mini D-sub 15-pin / mini D-sub 15-pin) (AAA size x2) • Power cord (1.8 m / 5.9') For Continental Europe • CD-ROM User's Manual / Supplement NMPJ Ver. 1.1 User's Manual - Canon REALiS WUX6000 Pro AV | User Manual - Page 29
Before Use Preparing the Remote Control ■ Installing Remote Control Batteries 1 Open the battery compartment close it. • If buttons on the remote control are inoperative when you attempt to operate the projector, replace the batteries with new ones. • Do not drop the remote control or subject it - Canon REALiS WUX6000 Pro AV | User Manual - Page 30
■ Remote Control Operating Range The remote control is an infrared type. Point it at the infrared remote receiver on the front or rear of the projector to operate it. 25° 8 m (26.3') 25° 8 m (26.3') 25° 25° • Use the remote control within an angle of 25° in any direction from directly in front - Canon REALiS WUX6000 Pro AV | User Manual - Page 31
Before Use Part Names Projector ■ Front Side Power cord connector (P138) Side control (P34) Lens unit Air intake vent Terminals and so may cause a malfunction. ■ Bottom Side Lamp cover Infrared remote receiver (P30) Screw holes for installation of ceiling attachment Adjustable feet (P118) 31 - Canon REALiS WUX6000 Pro AV | User Manual - Page 32
(10) (11) (3) (4) (12) (13) (14) (15) (5) (16) (17) (6) (18) (19) (7) (20) (1) POWER button (P38, P60) Turns the projector on or off. (2) FOCUS button (P44) Adjusts focusing. [ ] / [ ] buttons: Moves the focus position further away. [ ] / [ ] buttons: Moves the focus position nearer - Canon REALiS WUX6000 Pro AV | User Manual - Page 33
) VOL button (P63) Adjust the sound volume. [+] button: Increases the volume. [-] button: Decreases the volume. (16) P-TIMER button Cannot be used on this projector. (17) MUTE button (P63) Mutes the sound. (18) BLANK button (P62) Toggles between display / non-display of image. (19) LAMP button (P95 - Canon REALiS WUX6000 Pro AV | User Manual - Page 34
flashes under normal conditions. Lights up or flashes during standby or when the projector is shut down. Lights up or flashes when an error occurs. Flashes (1) (2) (7) (6) (5) (4) (3) (2) POWER button (P38, P60) Turns the projector on or off. (3) MENU button (P72) Displays a menu on the screen. - Canon REALiS WUX6000 Pro AV | User Manual - Page 35
Before Use Part Names ■ LED Indicator Displays The LED indicators flash or illuminate to indicate the operating status of the projector. : Off : Lit : Flashing LED indicator POWER ON (green) STAND BY (red) WARNING LAMP (red) (orange) TEMP (red) Operating status Not plugged in. In standby - Canon REALiS WUX6000 Pro AV | User Manual - Page 36
signals (HDMI). Carries both video and audio signals across a single cable. (8) LAN port (P164) Connects the LAN cable (shielded twisted pair). Used to connect the projector to a network. (9) Service port (CONTROL) It is not used during ordinary use. 36 - Canon REALiS WUX6000 Pro AV | User Manual - Page 37
Projecting an Image Appendix Installation and Maintenance Operation Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Other Information - Canon REALiS WUX6000 Pro AV | User Manual - Page 38
On 1 Check the connection between the projector and the computer or AV equipment. (P132 - P135) For instructions on connecting the power cord, refer to "Plugging the Projector In" (P138). 2 Press the POWER button. The [POWER ON] indicator initially flashes green, after which it remains lit - Canon REALiS WUX6000 Pro AV | User Manual - Page 39
multiple computers or multiple sets of AV equipment are connected. Skip this step if you have not changed the input signal since the last projection. Types of Input Signals The table below shows the relationship among input signals supported by the projector, input terminals and connection cables - Canon REALiS WUX6000 Pro AV | User Manual - Page 40
Step 2 Select an Input Signal Selecting an Input Signal 1 Press the INPUT button to display the window shown below. Remote control Projector The currently active input signal is marked with a green circle and enclosed by a orange border. An input signal that is ready for projection is displayed - Canon REALiS WUX6000 Pro AV | User Manual - Page 41
Panel Home] - [Appearance and Personalization], select [Adjust screen resolution]. 4 Select the resolution closest to the maximum output signal resolution of the projector from the [Resolution] list. 5 Click the [OK] button. ■ Windows 7 1 Open the [Control Panel] from the start menu, then select - Canon REALiS WUX6000 Pro AV | User Manual - Page 42
] - [Adjust screen resolution] in the [Control Panel Home]. 2 Under [Resolution], use the slider to select the resolution closest to the projector's maximum resolution. 3 Click the [OK] button. ■ Mac OS X 1 Open the Apple Menu and select [System Preferences]. 2 In the [System Preferences - Canon REALiS WUX6000 Pro AV | User Manual - Page 43
■ Performing the Auto PC Function Press the AUTO PC button to perform projector adjustment. Remote control If the Auto PC adjustment is insufficient, perform the [Vertical pixels] in [Input signal settings]. (P77, P78) • For the signal types supported by the projector, see the table on page 214. 43 - Canon REALiS WUX6000 Pro AV | User Manual - Page 44
, or Moving the Image Adjusting Image Focus To adjust the focus, press the FOCUS button on the remote control or the LENS button on the projector. For the projection distances of the lens unit, refer to "Relationship Between Image Size and Projecting Distance" on page 125. 1 Press either the FOCUS - Canon REALiS WUX6000 Pro AV | User Manual - Page 45
The size of the projected image can be adjusted by pressing the ZOOM button on the remote control or the LENS button on the projector. Change the projector installation position if your desired image is too large or too small to adjust it with the zoom function. (P118) 1 Press either the ZOOM button - Canon REALiS WUX6000 Pro AV | User Manual - Page 46
To adjust the screen position up, down, left, or right, press the LENS-SHIFT button on the remote control or the LENS button on the projector. It can change the projected screen to the most suitable position by moving the position of the lens up/ down/left/right. (P129) • The available - Canon REALiS WUX6000 Pro AV | User Manual - Page 47
position, perform reset. During screen position adjustment, press and hold the LENS-SHIFT button on the remote control or the LENS button on the projector to display the [Lens shift reset] window. The selections for the lens currently used are displayed. Use the pointer buttons to select one of - Canon REALiS WUX6000 Pro AV | User Manual - Page 48
the setting depending on the resolution of the computer or other AV equipment connected. If the image is not projected with the desired aspect menu window. Remote control Projector 2 Press the [ ] / [ ] buttons to select the [Install settings] tab. Remote control Projector When the Short Fixed - Canon REALiS WUX6000 Pro AV | User Manual - Page 49
3 Select [Screen aspect] with the [ ] / [ ] buttons, and then press the OK button. Remote control Projector Operation Projecting an Image 4 Use the [ ] / [ ] buttons to select the desired contents. Remote control Projector 16:10 Select this when you use a screen with an aspect ratio of 16:10 - Canon REALiS WUX6000 Pro AV | User Manual - Page 50
remote control, the D.SHIFT/KEYSTONE button. If you pressed the D.SHIFT/KEYSTONE on the remote control, go to step 4. 2 Press the [ ] / [ ] buttons to select the [Install settings] tab. Projector 3 Use the [ ] / [ ] buttons to select [Digital image shift], then press the OK button - Canon REALiS WUX6000 Pro AV | User Manual - Page 51
the [ ] / [ ] buttons to move the image up or down. Remote control Projector Operation Projecting an Image [ ] button: Moves the image up. Screen [ ] button: Press the [ ] / [ ] buttons to select the [Install settings] tab. Projector 3 Use the [ ] / [ ] buttons to select [Digital image shift], then - Canon REALiS WUX6000 Pro AV | User Manual - Page 52
Step 4 Select an Aspect Ratio (Screen Aspect) Matching the Screen 4 Use the [ ] / [ ] buttons to move the image. Remote control Projector [ ] button: Moves the image right. Screen [ ] button: Moves the image left. 5 When the image fits the screen, press the OK button. Resetting the Image - Canon REALiS WUX6000 Pro AV | User Manual - Page 53
Operation Projecting an Image Step 4 Select an Aspect Ratio (Screen Aspect) Matching the Screen 4:3 The image is projected using an input signal aspect ratio of 4:3. Select this if an image of 4:3 aspect ratio cannot be correctly projected in [Auto] mode. Zoom This cuts the upper/lower or left/ - Canon REALiS WUX6000 Pro AV | User Manual - Page 54
relative to each corner. For instructions on switching between the two types in memory. If you place the projector in the same position, the keystone Horizontal/Vertical Keystone Correction [Zoom] (P143) in the [Install settings] menu is not available during horizontal/vertical keystone correction. - Canon REALiS WUX6000 Pro AV | User Manual - Page 55
Operation Projecting an Image Step 5 Correct the Image Distortion 2 Press the pointer buttons to adjust the dimensions. Remote control [ ] button: Reduces the dimensions of the upper edge. [ ] button: Reduces the dimensions of the lower edge. Screen [ ] button: Reduces the dimension of the left - Canon REALiS WUX6000 Pro AV | User Manual - Page 56
have finished correcting, press the OK button. Corner adjustment settings will be cleared if you subsequently use [Zoom] (P143) in the [Install settings] menu. ■ Resetting the Keystone Adjustment Perform the following steps to reset the keystone adjustment. First, press the D.SHIFT/KEYSTONE button - Canon REALiS WUX6000 Pro AV | User Manual - Page 57
Operation Projecting an Image Step 6 Select the Image Quality (Image Mode) You can select an image mode to suit the projected image. In each image mode, you can further adjust the brightness, contrast, sharpness, gamma, color adjustment, advanced adjustment, and lamp mode. (P84) Image Modes - Canon REALiS WUX6000 Pro AV | User Manual - Page 58
Step 6 Select the Image Quality (Image Mode) ■ Selecting an Image Mode Press the IMAGE button on the remote control to select. The image mode changes each time the IMAGE button is pressed. (The displayed image modes vary depending on the selected input signal.) Remote control You can also select any - Canon REALiS WUX6000 Pro AV | User Manual - Page 59
Adjust lamp and fan power consumption in the image mode. • Power Management Mode (P98) Automatically turns off the lamp or projector after a certain period if the projector and remote control are idle and there is no video input signal. • Power Management Duration (P99) Automatically turns the power - Canon REALiS WUX6000 Pro AV | User Manual - Page 60
2 When this window is displayed, press the POWER button again to turn off the power. After you turn the power off, the projector will enter standby mode once it cools down. If you want to continue projecting without turning off the power, press a button other than POWER, or - Canon REALiS WUX6000 Pro AV | User Manual - Page 61
Functions Available During a Presentation Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Other - Canon REALiS WUX6000 Pro AV | User Manual - Page 62
to the proceedings of the presentation. • You want to stop a moving image. Remote control Press the FREEZE button to freeze the moving image. The projector shows the following icon. Screen Press the FREEZE button again to return to the original display. • It is also cancelled when the input signal - Canon REALiS WUX6000 Pro AV | User Manual - Page 63
external speakers. Remote control Press the VOL button. The following screen appears. • You can also adjust the volume level with the [ ] / [ ] buttons of the projector. • Adjust the volume or mute setting on the computer if the volume level is too low. • You can also adjust the volume level of the - Canon REALiS WUX6000 Pro AV | User Manual - Page 64
button to reduce the image size. • The magnification appears on the screen. You can move the enlarged area by using the buttons. Remote control Projector Screen Screen You can restore the original size of the image by pressing the OK button. The D.ZOOM buttons work differently than [Zoom] in - Canon REALiS WUX6000 Pro AV | User Manual - Page 65
's USB port. The USB flash drive will not be recognized if you connect it via a hub. 2 Press the INPUT button. Remote control Projector 3 Press the INPUT button repeatedly to select [USB]. JPEG files on the USB flash drive are now listed. • If the USB flash drive contains multiple - Canon REALiS WUX6000 Pro AV | User Manual - Page 66
on a USB Flash Drive 4 Use the pointer buttons to select a file, and then press the OK button to project the image. Remote control Projector Press the [ ] / [ ] buttons to select a file. To view another page, press the [ ] / [ ] buttons (if other pages are available). To navigate to a higher or - Canon REALiS WUX6000 Pro AV | User Manual - Page 67
sides. • Network and USB input cannot be combined for split-screen display. • [Zoom] (P143) in the [Install settings] menu is not available in split-screen mode. 1 Supply two signals to the projector. 2 Press the MENU button and then the [ ] / [ ] buttons to select the [Input settings] tab. 3 Use - Canon REALiS WUX6000 Pro AV | User Manual - Page 68
Split-Screen Display 4 Use the [ ] / [ ] buttons to select [On], and then press the OK button. • A number is displayed in the center of one image area. When the image at left is selected, 1 is displayed on the left, and when the image at right is selected, 2 is displayed on the right. The image - Canon REALiS WUX6000 Pro AV | User Manual - Page 69
Operation Useful Functions Available During a Presentation Split-Screen Display Side currently under control (input signal can be switched) Current input signal of side with control rights Current input signal of side without control rights To exit split-screen display, select [Input settings] tab - Canon REALiS WUX6000 Pro AV | User Manual - Page 70
70 - Canon REALiS WUX6000 Pro AV | User Manual - Page 71
Setting Functions from Menus Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Other Information Index - Canon REALiS WUX6000 Pro AV | User Manual - Page 72
Menu Configuration The menu screen is divided into 6 tabs as shown below. [Install settings] tab This setting is used when installing the projector. [System settings] tab You can set the operation of the projector. [Image adjustment] tab You can adjust the image quality and colors according to - Canon REALiS WUX6000 Pro AV | User Manual - Page 73
press the [ ] / [ ] buttons to move the current selection to the top. 3 Press the [ ] / [ ] buttons to select an item. Remote control Projector 4 Select contents. How to select the contents varies depending on the item. Selecting from a list Example: Aspect (P75) 1. Select [Aspect]. 2. Press the - Canon REALiS WUX6000 Pro AV | User Manual - Page 74
screen (1) Example: Menu position (P149) 1. Select [Menu position]. 2. Press the OK button to display a different screen. 3. Then follow the instruction on the screen. Selecting from a different screen (2) Example: Tracking (P77) 1. Select [Input signal settings]. 2. Press the OK button to display - Canon REALiS WUX6000 Pro AV | User Manual - Page 75
Operation Setting Functions from Menus Setting Display Status (Input Settings) Selecting the Aspect > [Input settings] > [Aspect] HDMI Digital PC Component Analog PC LAN USB You can select a projection mode corresponding to the aspect ratio of the image. (P52) • For LAN and USB input, [Auto] - Canon REALiS WUX6000 Pro AV | User Manual - Page 76
[Total dots], [Tracking], [Horizontal/Vertical position] and [Horizontal/Vertical pixels] in [Input signal settings]. (P77, P78) • For the signal types supported by the projector, see the table on page 214. Select an input signal corresponding to the resolution of the computer. Press the OK button - Canon REALiS WUX6000 Pro AV | User Manual - Page 77
Operation Setting Functions from Menus Setting Display Status (Input Settings) Adjusting the Input Signal (Total dots) > [Input settings] > [Input signal settings] > [Total dots] HDMI Digital PC Component Analog PC LAN USB You can adjust the total number of dots in the horizontal direction. - Canon REALiS WUX6000 Pro AV | User Manual - Page 78
Setting Display Status (Input Settings) Adjusting the Input Adjusting the Input Signal Signal (Horizontal / Vertical position) (Horizontal / Vertical pixels) > [Input settings] > [Input signal settings] > [Horizontal position] / [Vertical position] HDMI Digital PC Component Analog PC LAN USB - Canon REALiS WUX6000 Pro AV | User Manual - Page 79
] or [Expanded] for [HDMI input level]. For more detailed information, refer to the user's manual for the AV equipment connected to the projector. Auto Selects the optimal color format for the input HDMI signal. RGB Forces the projector to handle the input signal as an RGB signal. YCbCr Forces the - Canon REALiS WUX6000 Pro AV | User Manual - Page 80
Setting Display Status (Input Settings) Specifying HDMI Overscan > [Input settings] > [HDMI over scan] HDMI Digital PC Component Analog PC LAN USB When projecting images in videos via HDMI, select this setting to trim distorted image edges. Specifying Progressive Processing > [Input settings - Canon REALiS WUX6000 Pro AV | User Manual - Page 81
Setting Display Status (Input Settings) • [Film/auto] is the factory default. • Select [Off] when flickers and horizontal lines are noticeable in media that has a lot of fast-moving action. • Not available during split-screen display. Specifying the Slideshow Interval > [Input settings] > [ - Canon REALiS WUX6000 Pro AV | User Manual - Page 82
Setting Display Status (Input Settings) Specifying SplitScreen Display > [Input settings] > [Split screen] HDMI Digital PC Component Analog PC LAN USB You can project two input images side by side. (P67) Press the OK button to accept your setting and then press the MENU button. The image with - Canon REALiS WUX6000 Pro AV | User Manual - Page 83
Adjusting Image Quality (Image Adjustment) Specifying Image Priority in Split-Screen Mode > [Image adjustment] > [Image priority] HDMI Digital PC Component Analog PC LAN USB Some image processing in splitscreen mode is applied to both sides. Here, select which side to use as the primary side, - Canon REALiS WUX6000 Pro AV | User Manual - Page 84
Adjusting Image Quality (Image Adjustment) Specifying the Image Mode > [Image adjustment] > [Image mode] HDMI Digital PC Component Analog PC LAN USB You can select an image mode (P57) suitable for the projected image. You can also select it with the IMAGE button on the remote control. (P58) - Canon REALiS WUX6000 Pro AV | User Manual - Page 85
to save different settings for when the connected equipment is a computer (ANALOG PC, DIGITAL PC or HDMI (when [HDMI In] (P108) is [Computer]) and when AV equipment is connected (COMPONENT, HDMI (when [HDMI In] (P108) is [Auto])). As a result, it is possible to save up to 10 settings. 85 - Canon REALiS WUX6000 Pro AV | User Manual - Page 86
Adjusting Image Quality (Image Adjustment) Adjusting Brightness > [Image adjustment] > [Brightness] HDMI Digital PC Component Analog PC LAN USB You can adjust the brightness of images. Adjusting Contrast > [Image adjustment] > [Contrast] HDMI Digital PC Component Analog PC LAN USB You - Canon REALiS WUX6000 Pro AV | User Manual - Page 87
Operation Setting Functions from Menus Adjusting Image Quality (Image Adjustment) Adjusting Sharpness > [Image adjustment] > [Sharpness] HDMI Digital PC Component Analog PC LAN USB You can adjust the sharpness of images. Correcting Gamma > [Image adjustment] > [Gamma] HDMI Digital PC - Canon REALiS WUX6000 Pro AV | User Manual - Page 88
Adjusting Image Quality (Image Adjustment) Adjusting Colors > [Image adjustment] > [Color adjustment] HDMI Digital PC Component Analog PC LAN USB You can adjust the color depth and hue of images for each primary color, red, green and blue. The color temperature can also be adjusted. R / G / B - Canon REALiS WUX6000 Pro AV | User Manual - Page 89
Operation Setting Functions from Menus Adjusting Image Quality (Image Adjustment) Adjusting to the Ambient Light (Ambient Light) > [Image adjustment] > [Advanced adjustment] > [Ambient light] HDMI Digital PC Component Analog PC LAN USB You can compensate for ambient light on the screen. The [ - Canon REALiS WUX6000 Pro AV | User Manual - Page 90
Adjusting Image Quality (Image Adjustment) Reducing Image Noise (Random noise reduction) Reducing Image Noise (MPEG noise reduction) > [Image adjustment] > [Advanced adjustment] > [Random noise reduction] HDMI Digital PC Component Analog PC LAN USB > [Image adjustment] > [Advanced adjustment] - Canon REALiS WUX6000 Pro AV | User Manual - Page 91
Operation Setting Functions from Menus Adjusting Image Quality (Image Adjustment) Reducing Image Noise (Mosquito noise reduction) > [Image adjustment] > [Advanced adjustment] > [Mosquito noise reduction] HDMI Digital PC Component Analog PC LAN USB You can reduce mosquito noise. Dynamic Gamma - Canon REALiS WUX6000 Pro AV | User Manual - Page 92
Adjusting Image Quality (Image Adjustment) Correcting Memory Color > [Image adjustment] > [Advanced adjustment] > [Mem. color correct] HDMI Digital PC Component Analog PC LAN USB Enhances skin tones, blue skies, and greens, so that these colors are more consistent with people's remembered - Canon REALiS WUX6000 Pro AV | User Manual - Page 93
Adjusting Image Quality (Image Adjustment) • [Off] is the factory default. • The adjustments you have made are stored as adjusted values for the input signals and image mode of the current projection. • Adjustments are not applied to the displayed menu screen itself. Fine-Tuning Gamma > [Image - Canon REALiS WUX6000 Pro AV | User Manual - Page 94
changes from fully black. Press the OK button to accept your setting and then press the MENU button. • [Off] is the factory default. • The projector automatically enters standby mode if the lamp is dimmed (that is, if the input signal is fully black) for more than one hour. A countdown window - Canon REALiS WUX6000 Pro AV | User Manual - Page 95
Adjusting Image Quality (Image Adjustment) Specifying the Lamp Mode > [Image adjustment] > [Lamp mode] HDMI Digital PC Component Analog PC LAN USB Reducing the lamp brightness reduces power consumption and cooling fan noise. Resetting Image Adjustment Settings > [Image adjustment] > [Reset] - Canon REALiS WUX6000 Pro AV | User Manual - Page 96
Customizing System Operation (System Settings) Registering User Logos > [System settings] > [User screen settings] > [Logo capture] HDMI Digital PC Component Analog PC LAN USB Registers the current image as a user logo. Registered user logos can be shown when no signal is received, when the - Canon REALiS WUX6000 Pro AV | User Manual - Page 97
Customizing System Operation (System Settings) No Signal Screen > [System settings] > [User screen settings] > [No signal screen] HDMI Digital PC Component Analog PC LAN USB As the image projected when there is no input signal, you can choose a black, blue, or registered user screen. Screen - Canon REALiS WUX6000 Pro AV | User Manual - Page 98
remote control are not used and there is no input signal. Skip Canon logo User logo Projects an input signal immediately after turning on the projector. Displays the Canon logo that was registered in advance at the factory. The user logo is projected. Press the OK button to accept your setting - Canon REALiS WUX6000 Pro AV | User Manual - Page 99
. Specifying Direct Power-On > [System settings] > [Direct power on] HDMI Digital PC Component Analog PC LAN USB You can turn on the projector by connecting the power cable without pressing the POWER button. Operation Setting Functions from Menus 5 min. 60 min. After 30 seconds without an - Canon REALiS WUX6000 Pro AV | User Manual - Page 100
PC Component Analog PC LAN USB By pressing and holding the button on the projector or the remote control you can operate Key repeat in the same way factory default is [On]. • The beep will not sound if you mute the projector sound with the MUTE button on the remote control. Off Key repeat is not - Canon REALiS WUX6000 Pro AV | User Manual - Page 101
. Disables infrared remote control operations (P30). Use buttons on the main unit. Alternatively, use the optional remote control (RS-RC05), connected to the projector via a cable. Press the OK button to accept your setting and then press the MENU button. • [Off] is the factory default. When you - Canon REALiS WUX6000 Pro AV | User Manual - Page 102
channel can be used. Press the OK button to accept your setting and then press the MENU button. • The factory default is [Independent] for both projector and remote control. • After changing the channel on the menu, be sure to change the channel of the remote control too. • If an optional wired - Canon REALiS WUX6000 Pro AV | User Manual - Page 103
Customizing System Operation (System Settings) Reducing Motion Blur > [System settings] > [Motion blur reduction] HDMI Digital PC Component Analog PC LAN USB Motion blur is blurring that occurs during video playback. Motion blur reduction can make this blurring less noticeable. Selecting a - Canon REALiS WUX6000 Pro AV | User Manual - Page 104
from the remote control, in standby state press the MENU button 3 times, then press the POWER button. Off The projector can be used even if no password is entered. On The projector cannot be used unless you enter your password. Press the OK button to accept your setting and then press the - Canon REALiS WUX6000 Pro AV | User Manual - Page 105
Operation Setting Functions from Menus Customizing System Operation (System Settings) Setting a Password > [System settings] > [Other settings] > [Register password] HDMI Digital PC Component Analog PC LAN USB You can register a password for starting projection. Using the Remote Control [Fn] - Canon REALiS WUX6000 Pro AV | User Manual - Page 106
Customizing System Operation (System Settings) Selecting Audio Input > [System settings] > [Other settings] > [Audio in terminal select] HDMI Digital PC Component Analog PC LAN USB You can select the audio input terminal to use for each type of input signal. • The factory defaults are as - Canon REALiS WUX6000 Pro AV | User Manual - Page 107
or longer. If Gamma restore is performed, the tone characteristics and achromatic color will be restored as close as possible to the condition when the projector was purchased, however it is not possible to restore it completely to the original condition. So the changing and turning color cannot be - Canon REALiS WUX6000 Pro AV | User Manual - Page 108
counter cannot indicate the correct timing for replacing the lamp. For details of lamp replacement, refer to page 197. Auto Select when AV equipment will be connected. Image processing, menu displays, and other elements are adjusted for video equipment. Computer Select when a computer will be - Canon REALiS WUX6000 Pro AV | User Manual - Page 109
Operation Setting Functions from Menus Customizing System Operation (System Settings) Over 3,000 hours Displayed as a green, yellow and red bar. Select [Yes] on the screen for confirmation and press the OK button to reset the lamp counter. Press the MENU button. ■ About the Display of the Lamp - Canon REALiS WUX6000 Pro AV | User Manual - Page 110
[Firmware] HDMI Digital PC Component Analog PC LAN USB Update the projector firmware as follows. Save firmware updates from the Canon website to the not be possible to download updates. For details, contact the Canon Customer Support Center. To view the air filter counter, press the OK button - Canon REALiS WUX6000 Pro AV | User Manual - Page 111
Customizing System Operation (System Settings) Resetting to the Default Setting > [System settings] > [Other settings] > [Factory defaults] HDMI Digital PC Component Analog PC LAN USB You can reset the menu item settings and restore the system settings to the factory defaults. - [Create - Canon REALiS WUX6000 Pro AV | User Manual - Page 112
e-mail address has been set for receiving error mails. (P183) Projector name* Name which identifies this projector on the network Comments* Comments such as the location in which the projector is installed are displayed. (P186) System information System information. Normally this is not - Canon REALiS WUX6000 Pro AV | User Manual - Page 113
Installation Appendix Installation and Maintenance Operation Installation and Maintenance Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Other - Canon REALiS WUX6000 Pro AV | User Manual - Page 114
a qualified technician or contact the Canon Customer Support Center. Precautions for Installation Be sure to read "Safety Instructions" and "For Safe Use" (P10 - P23). Also take the following precautions during installation. • Do not strike the projector or Air intake vent subject it to impact - Canon REALiS WUX6000 Pro AV | User Manual - Page 115
Distance from Walls and Other Obstructions If the air intake or exhaust vent is blocked, heat will accumulate inside the projector, possibly resulting in a shortened projector lifetime or a malfunction. Do not install in a closet, on a bookshelf, or in other narrow spaces with poor ventilation - Canon REALiS WUX6000 Pro AV | User Manual - Page 116
at altitudes of 2,300 m (7,545.8') or higher. Specifically, refer to instructions for [Fan mode] (P146) in the [Install settings] menu. ■ When Using Mounted on the Ceiling When the projector is used mounted on the ceiling or installed in a high location, it is necessary to periodically clean the air - Canon REALiS WUX6000 Pro AV | User Manual - Page 117
or downward projection, refer to instructions for [Vertical projection] (P147) in the [Install settings] menu. • Do not attempt to install the projector for upward or downward projection by yourself. Always request installation by a qualified technician or the Canon Customer Support Center. 10° 10 - Canon REALiS WUX6000 Pro AV | User Manual - Page 118
turned off, curtains be drawn, and other steps taken to make the screen easier to see. Screen Optical axis ■ Floor Installation To adjust the projection position when the projector is installed on the floor, use the lens shift function (P46, P129) to adjust up / down / left / right. You can also - Canon REALiS WUX6000 Pro AV | User Manual - Page 119
installation manual provided with the ceiling attachment. Mounting the Projector on the Ceiling You can mount the projector projector on the ceiling. Depending on the installation environment, an extension pipe (part No.: RS-CL08 or RS-CL09) may also be required. Contact the Canon Customer Support - Canon REALiS WUX6000 Pro AV | User Manual - Page 120
result in parts falling off the projector and may cause an accident or personal injury. • Do not attempt to install or remove the lens unit yourself. Be sure to request this service from a qualified technician or contact the Canon Customer Support Center. • When installing and removing the lens unit - Canon REALiS WUX6000 Pro AV | User Manual - Page 121
and Maintenance Installation Installation Procedure 2 Loosen the cosmetic panel screw, then slide the cosmetic panel toward on top and 2 on bottom). After the 2 screws on top are removed, turn the projector upside down on a flat desk or similar location and remove the 2 screws from the bottom. 121 - Canon REALiS WUX6000 Pro AV | User Manual - Page 122
Installation Procedure 5 Then turn the projector back over and remove the sleeve. 6 Referring to the following illustration, insert the lens connector of the lens unit into the front right side of the projector slowly until it contacts the end. At this time, pull out the lens cable shown in the - Canon REALiS WUX6000 Pro AV | User Manual - Page 123
and Maintenance Installation Installation Procedure 8 Insert the projector lens cable into the connector until a click sound is heard. 9 Reinstall the sleeve, cosmetic panel, and lamp cover in their original positions. When the power is first turned on after the lens unit has been installed or - Canon REALiS WUX6000 Pro AV | User Manual - Page 124
Procedure ■ Removing the Lens Unit 1 Perform steps 1 to 5 of "Installing the Lens Unit" (P120 - P122) to remove the sleeve. 2 Disconnect the lens cable from the lens connector. When pulling out (disconnecting) the lens cable, press - Canon REALiS WUX6000 Pro AV | User Manual - Page 125
Installation Installation Procedure Relationship Between Image Size and Projecting Distance The projected image size is determined by the distance between the projector Fixed Lens: 0% (up / down / left / right) WUX6000 Projection Distance from Image size (cm) distance optical axis Diagonal - Canon REALiS WUX6000 Pro AV | User Manual - Page 126
Installation Procedure Projection Distance from Image size (cm) distance optical axis Diagonal Lens unit when 16:10 16:10 16:9 m (feet) when projection 4:3 16:10 is - Canon REALiS WUX6000 Pro AV | User Manual - Page 127
and Maintenance Installation Installation Procedure Projection Distance from Image size (cm) distance optical axis Diagonal Lens unit when 16:10 16:10 16:9 m (feet) when projection 4:3 16:10 is - Canon REALiS WUX6000 Pro AV | User Manual - Page 128
Installation Procedure Projection Distance from Image size (cm) distance optical axis Diagonal Lens unit when 16:10 16:10 16:9 m (feet) when projection 4:3 16:10 is - Canon REALiS WUX6000 Pro AV | User Manual - Page 129
and Maintenance Installation Installation Procedure Lens Shift Function The projector includes a lens shift function. Operation of the buttons slides the lens up, down, left, and right, moving the image position. For instructions, refer to "Adjusting the Image Position" (P46). The amount - Canon REALiS WUX6000 Pro AV | User Manual - Page 130
Installation Procedure Area Outside the Lens Shift Range With the Standard Zoom Lens, Long Zoom Lens, Ultra Long Zoom Lens, and Wide Zoom Lens, when the - Canon REALiS WUX6000 Pro AV | User Manual - Page 131
Installation AUDIO OUT terminal Amplified speakers (P134, P137) LAN LAN terminal Network (P164) Service Port (It is not used during ordinary use.) USB USB Port USB Flash Drive terminal Computer (P132, P133) AV equipment (P135) AV equipment (P136) Digital video camera* (P135) Computer ( - Canon REALiS WUX6000 Pro AV | User Manual - Page 132
To AUDIO IN terminal 2 Audio cable (not included) Connecting with DVI-D-sub 15 cable (Input signal type: [Analog PC-1] P39) Computer Projector Monitor output terminal (Mini D-sub 15-pin) AUDIO output terminal (AUDIO OUT) DVI-D-sub 15 cable (not included) When inputting corresponding audio - Canon REALiS WUX6000 Pro AV | User Manual - Page 133
and Maintenance Installation Connection Procedure • Use a DVI-D-sub 15 cable in which all terminal converter cable (not included) Mini D-sub 15-pin BNC terminal converter cable (not included) Projector To ANALOG PC-2 / COMPONENT terminal Monitor output terminal (Mini D-sub 15-pin) BNC cable - Canon REALiS WUX6000 Pro AV | User Manual - Page 134
the same time. To HDMI terminal ■ Outputting Audio to Speakers It is possible to output audio from the projected images to amplified speakers. Projector Speaker To AUDIO OUT terminal RCA terminal Audio cable (not included) Mini jack AUDIO IN terminal (AUDIO IN) • Use an audio cable without - Canon REALiS WUX6000 Pro AV | User Manual - Page 135
Installation Connection Procedure Connecting AV Equipment Connect the projector and AV equipment. The description provided here is one example. For more detailed information, refer to the manual for the connected AV equipment. Before connecting the cables, turn off both the projector and AV - Canon REALiS WUX6000 Pro AV | User Manual - Page 136
's COMPONENT terminal. Use a commercially available component cable (not included) that fits the terminal type of the AV equipment to create a relay connection. AV equipment Projector RCA plug - RCA plug Component cable (not included) RCA component terminal D terminal Video output terminal To - Canon REALiS WUX6000 Pro AV | User Manual - Page 137
Connection Procedure ■ Outputting Audio to Speakers It is possible to output audio from the projected images to AV equipment or amplified speakers. Projector Speaker To AUDIO OUT terminal Audio cable (not included) RCA terminal Mini jack AUDIO IN terminal (AUDIO IN) Use an audio cable without - Canon REALiS WUX6000 Pro AV | User Manual - Page 138
In Connect the power cord to the projector and plug it in. Connect the ground terminal on the power plug to ground . • Fully insert the power cord plug into the socket. • After turning off the projector, wait at least 5 minutes before turning it on again. It may shorten the lamp life if you turn on - Canon REALiS WUX6000 Pro AV | User Manual - Page 139
Installation and Maintenance Installation Starting Projection Starting and Stopping Projection ■ Starting Projection Press the POWER button on the remote control or on the projector. The [POWER ON] indicator initially flashes green, after which it remains lit. Remote control Projector ■ - Canon REALiS WUX6000 Pro AV | User Manual - Page 140
. • The function key you use and the method used to turn on the external monitor output vary depending on the model. For details, see the manual for your notebook computer. • With Windows 8.1, Windows 8 or Windows 7, you can turn on image output by holding down the Windows logo key and pressing the - Canon REALiS WUX6000 Pro AV | User Manual - Page 141
PC Component Analog PC LAN USB Select this setting if you want to hang the projector from the ceiling or project an image from behind the screen. Installation and Maintenance Installation Off The positional lock is not used. On Prevents adjustment of installationrelated functions. Press the - Canon REALiS WUX6000 Pro AV | User Manual - Page 142
> [Install settings] > [Screen aspect] HDMI Digital PC Component Analog PC LAN USB Select according to the aspect ratio of the projection screen. (P48) Rear projection Rear, Ceiling Mounting • To hang the projector from the ceiling, use the optional bracket. Contact the Canon Customer Support - Canon REALiS WUX6000 Pro AV | User Manual - Page 143
image shift setting. • [Auto] may be automatically selected for the aspect depending on the screen aspect setting. Adjusting the Size of Projected Images > [Install settings] > [Zoom] HDMI Digital PC Component Analog PC LAN USB With the Short Fixed Lens, projected images that do not fit on the - Canon REALiS WUX6000 Pro AV | User Manual - Page 144
fit on the screen. • Switching to lenses other than the Short Fixed Lens will reset the setting to 100%. Specifying Keystone Correction > [Install settings] > [Keystone] HDMI Digital PC Component Analog PC LAN USB Two types of keystone correction are available: horizontal-vertical keystone and - Canon REALiS WUX6000 Pro AV | User Manual - Page 145
shift] HDMI Digital PC Component Analog PC LAN USB Use this setting to fine-tune the position of the projected image. Installation and Maintenance Installation Press the OK button or [ ] button to display the D. image shift adjustment screen. Off Does not perform micro digital image shift - Canon REALiS WUX6000 Pro AV | User Manual - Page 146
PC Component Analog PC LAN USB Adjusts colors that are out of alignment. You can adjust red, green and blue registration independently. > [Install settings] > [Professional settings] > [Fan mode] HDMI Digital PC Component Analog PC LAN USB Enable suitable cooling by switching the fan mode to - Canon REALiS WUX6000 Pro AV | User Manual - Page 147
be saved, and the lens can be restored to these positions. Installation and Maintenance Installation Off Does not alter the fan mode. Upward Setting for use when the projector faces upward Downward Setting for use when the projector faces downward When the setting is completed, press the OK - Canon REALiS WUX6000 Pro AV | User Manual - Page 148
off the screen. • When precise positioning is needed, use lens shift, zoom, and focus functions for fine adjustment. Screen Color Adjustment > [Install settings] > [Screen color] HDMI Digital PC Component Analog PC LAN USB You can adjust the color quality of the images projected according to - Canon REALiS WUX6000 Pro AV | User Manual - Page 149
the position of menus displayed. Installation-Related Menu Settings Showing/Hiding the Guide Screen > [Install settings] > [On screen] > [Guide] HDMI Digital PC Component Analog PC positional lock is set to [On]. (P141) - When the projector is already on and the POWER button is pressed. 149 - Canon REALiS WUX6000 Pro AV | User Manual - Page 150
the screen when there is no signal or when making signal settings. > [Install settings] > [On screen] > [Overheat warning display] HDMI Digital PC the [High temperature warning] icon when the temperature inside the projector has increased and is approaching the overheat temperature. Off The input - Canon REALiS WUX6000 Pro AV | User Manual - Page 151
the lamp has been used for the specified period of time. Installation and Maintenance Installation Normal Extended The menu is displayed for 10 or 30 seconds. it is time to replace the lamp, the LAMP indicator on the projector will flash, and lamp replacement (P199) is recommended at this time. - Canon REALiS WUX6000 Pro AV | User Manual - Page 152
] HDMI Digital PC Component Analog PC LAN USB A message advising you to perform cleaning can be set to display when the filter needs cleaning. > [Install settings] > [On screen] > [Split screen ID display] HDMI Digital PC Component Analog PC LAN USB Specify whether to show or hide the digit - Canon REALiS WUX6000 Pro AV | User Manual - Page 153
-Related Menu Settings Displaying Test Patterns > [Install settings] > [Test pattern] HDMI Digital PC Component Analog PC LAN USB You can project a test pattern (P213) to check resolution, color, and other details even - Canon REALiS WUX6000 Pro AV | User Manual - Page 154
Once (Edge Blending) > [Install settings] > [Professional settings] > [Edge blending] HDMI Digital PC Component Analog PC LAN USB Overlapping edges of images from multiple projectors used together can be blended to make the overall image more seamless. ■ Basic Instructions Follow these steps - Canon REALiS WUX6000 Pro AV | User Manual - Page 155
and Maintenance Installation Installation-Related Menu Settings Here, you can use the following settings in the edge blending menu. Off Adjust Side Left, Width Right, Top, Start Bottom position - Canon REALiS WUX6000 Pro AV | User Manual - Page 156
Installation-Related Menu Settings 5 Use the remote control's [ ] button to select [Start position], and of the starting marker. 7 Set [Marker] to [Off]. Edge Blending with Four Projectors Images from four projectors can also be blended, as shown at left. Specify the blending area where each image - Canon REALiS WUX6000 Pro AV | User Manual - Page 157
and Maintenance Installation Installation-Related Menu Settings ■ Advanced Instructions: Color Adjustment In overlapping projection, portions of images in the overlapping area that , and 3 then adjust [Red], [Green], and [Blue] values individually. Repeat this adjustment on all projectors. 157 - Canon REALiS WUX6000 Pro AV | User Manual - Page 158
Installation-Related Menu Settings ■ Advanced Instructions: Black Level Adjustment In overlapping projection Normally, three areas are identified in the context of end markers: A, B, and C. In the following instructions, only area D is adjusted, and the widths of A, B, and C are left at the default - Canon REALiS WUX6000 Pro AV | User Manual - Page 159
the blue component of the area D black level. 2 Select [Adjustment type] > [Black level]. Installation and Maintenance Installation 3 Select [D-area base], and use the remote's [ ] [ ] buttons to adjust the values black level color tone, as needed. 4 Repeat this adjustment on all projectors. 159 - Canon REALiS WUX6000 Pro AV | User Manual - Page 160
Installation-Related Menu Settings ■ Advanced Instructions: Smoother Overlapping Areas Adjustments to areas A, B, and C may make the black level along the right edge of area D (that is, the edge bordering the blending - Canon REALiS WUX6000 Pro AV | User Manual - Page 161
and Maintenance Installation Installation-Related Menu Settings 2 Select [B-width], and use the remote's blue Adjust the blue component of the area B black level. For adjustment instructions, see "Advanced Instructions: Black Level Adjustment" (P158), step 3. Results of adjusting the black level - Canon REALiS WUX6000 Pro AV | User Manual - Page 162
162 - Canon REALiS WUX6000 Pro AV | User Manual - Page 163
Connecting to a Network Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Other Information Index 163 - Canon REALiS WUX6000 Pro AV | User Manual - Page 164
IP address does not overlap with other computers that are on the same LAN. To set a projector IP address, follow the instructions in "Completing Computer Settings" (P173) and use the web screen, or use projector TCP/IP settings. (P169) • When you connect the computer to the network for the first - Canon REALiS WUX6000 Pro AV | User Manual - Page 165
[Network Setting] tab. For instructions on menu operations, refer to "Using Menus". (P72) Locking/Unlocking Network Settings > [Network Settings] > [Network settings lock] You can lock/unlock the network settings so that they cannot be changed. Installation and Maintenance Connecting to a Network - Canon REALiS WUX6000 Pro AV | User Manual - Page 166
the Network Password > [Network settings] > [Network password setting] You can set whether or not a password is required in order to change the projector network settings. Off A network password is not used. On A network password is used. Press the OK button to accept your setting and then press - Canon REALiS WUX6000 Pro AV | User Manual - Page 167
Installation and Maintenance Connecting to a Network Registering a Network Password > [Network settings] > [Register network password] Register the projector network password. Completing Projector Settings Specifying Standby Power Consumption > [Network settings] > [Network standby settings] - Canon REALiS WUX6000 Pro AV | User Manual - Page 168
Off] is the factory default. Viewing the IP Address, Gateway Address, and MAC Address > [Network settings] > [Detailed settings] > [IP address] View the projector's IP address as follows. Note that the information can only be displayed, not changed. To change the settings, access the DHCP or TCP/IP - Canon REALiS WUX6000 Pro AV | User Manual - Page 169
Installation and Maintenance Connecting to a Network Specifying DHCP > [Network settings] > [Detailed settings] > [DHCP] You can enable or disable the DHCP function of the projector. Completing Projector Settings Specifying TCP/IP Settings > [Network settings] > [Detailed settings] > [TCP/IP - Canon REALiS WUX6000 Pro AV | User Manual - Page 170
conforms to Class 1 as defined in the PJLink standards of the JBMIA (Japan Business Machine and Information System Industries Association). This projector supports all commands that are defined by PJLink Class 1, and has been verified as conforming to the PJLink standard Class 1 definition. • For - Canon REALiS WUX6000 Pro AV | User Manual - Page 171
Installation and Maintenance Connecting to a Network What is PJLink? In September 2003, the PJLink Working Group was established under the Data Projector Committee. During the first year, this PJLink Working Group standardized PJLink as a new interface specification for projectors. PJLink is a - Canon REALiS WUX6000 Pro AV | User Manual - Page 172
settings] > [Crestron RoomView] Crestron RoomView enables centralized management of multiple projectors over a network. For example, projectors can be remotely controlled to troubleshoot issues, check the useful life of lamps, or turn the projectors on or off. Specify whether or not to use Crestron - Canon REALiS WUX6000 Pro AV | User Manual - Page 173
Installation and Maintenance Connecting to a Network Completing Computer Settings Specifying an IP Address Following is IP address] and set the IP address and subnet mask. The factory default IP address for the projector is "192.168.254.254". Set an IP address which is different from this. 173 - Canon REALiS WUX6000 Pro AV | User Manual - Page 174
mask, default gateway, etc). 6 Select [Use the following IP address] and set the IP address and subnet mask. The factory default IP address for the projector is "192.168.254.254". Set an IP address which is different from this. 174 - Canon REALiS WUX6000 Pro AV | User Manual - Page 175
192.168.254.1 Subnet mask: 255.255.255.0 Completing Computer Settings Installation and Maintenance Connecting to a Network 7 When the settings are completed, click mask. The factory default IP address for the projector is "192.168.254.254". Set an IP address which is different from this. 175 - Canon REALiS WUX6000 Pro AV | User Manual - Page 176
, subnet mask, router, DNS server, etc.). 4 Create a new network environment and set the IP address and subnet mask. The factory default IP address for the projector is "192.168.254.254". Set an IP address which is different from this. 176 - Canon REALiS WUX6000 Pro AV | User Manual - Page 177
Installation and Maintenance Connecting to a Network Example IP address: 192.168.254.1 Subnet 1 Turn on the computer and projector. Network functions are not available for the first 40 seconds after projector startup. 2 Launch a web browser, enter "http://(projector IP address)" in the address bar - Canon REALiS WUX6000 Pro AV | User Manual - Page 178
projector is installed MAC address The MAC address of the projector IP address PowerStatus The IP address of the projector The power status of the projector manual. The factory default IP address is "192.168.254.254". If DHCP settings are used, ask the network administrator for the projector IP - Canon REALiS WUX6000 Pro AV | User Manual - Page 179
Installation and Maintenance Connecting to a Network Completing Computer Settings The projector settings screen is displayed in the web browser. To operate the projector from the computer, click [Projector control]. (P191) ■ Network Setting 1 To access the settings screen, click [Settings] on the - Canon REALiS WUX6000 Pro AV | User Manual - Page 180
Computer Settings 3 A confirmation window appears. Check the contents and if they are correct, click [Apply]. The settings are applied to the projector. Selecting [Network] or [Password] in the menu will cause this message to be displayed: "Save completed. Please change setting and reconnect - Canon REALiS WUX6000 Pro AV | User Manual - Page 181
network information. For the setting procedure, refer to "Network Setting" (P179). Installation and Maintenance Connecting to a Network Item MAC address DHCP IP address Subnet mask Default gateway Explanation Shows the projector's MAC address. Select whether to turn the DHCP function on or off - Canon REALiS WUX6000 Pro AV | User Manual - Page 182
). For confirmation, enter the same password as you entered in [Password]. For details on Networked Multi-Projection (NMPJ), refer to the separate user's manual. 182 - Canon REALiS WUX6000 Pro AV | User Manual - Page 183
. For the setting procedure, refer to "Network Setting" (P179). Installation and Maintenance Connecting to a Network Item To: Cc: From: SMTP SNTP server IP address in 1-byte numbers. Select the time zone where the projector is used. Enter the interval for resending mail when an error occurred ( - Canon REALiS WUX6000 Pro AV | User Manual - Page 184
Completing Computer Settings Mail Authentication Settings [Mail auth] From [Mail auth] in the settings screen, you can configure the settings for authentication of mail that is sent when an error occurs. For the setting procedure, refer to "Network Setting" (P179). Item Mail authentication User - Canon REALiS WUX6000 Pro AV | User Manual - Page 185
. SNMP Settings [SNMP] From [SNMP] in the settings screen, you can configure the settings related to control of projectors which use SNMP (Simple Network Management Protocol). For the setting procedure, refer to "Network Setting" (P179). Installation and Maintenance Connecting to a Network 185 - Canon REALiS WUX6000 Pro AV | User Manual - Page 186
info.] in the settings screen, you can enter relevant comments such as projector names and locations where projectors are installed so that the information can be used to identify projectors when multiple projectors are installed on the network. For the setting procedure, refer to "Network Setting - Canon REALiS WUX6000 Pro AV | User Manual - Page 187
Installation and Maintenance Connecting to a Network Completing Computer Settings Setting PJLink [PJLink] From [PJLink] in the settings screen, you can set the PJLink functions which are the standard for projector management on a network. For the setting procedure, refer to "Network Setting" (P179 - Canon REALiS WUX6000 Pro AV | User Manual - Page 188
when sending a test mail. Failed to connect to the POP3 server attempting to send a test mail. An authentication type was set which is not supported by the server. Authentication failed attempting to send a test mail. Sending of test mail failed due to a connection failure with the SMTP server or - Canon REALiS WUX6000 Pro AV | User Manual - Page 189
is too high for some reason or the outside air temperature is higher than the specified one. If the problem is inside the projector, check whether the projector is installed and operated normally, turn off the projector to cool its inside, and retry projection. If the same warning occurs again, the - Canon REALiS WUX6000 Pro AV | User Manual - Page 190
lens connector Error name Text Error name Text Faulty power supply The voltage of part of the power supply is abnormally high or any other problem has occurred in the power supply. Contact your dealer. Faulty lens connector The lens cable is not connected to the lens unit. Check whether the - Canon REALiS WUX6000 Pro AV | User Manual - Page 191
Installation and Maintenance Connecting to a Network Completing Computer Settings Control via the Web Screen When the projector is connected to a network, it is possible to control the projector from a computer via the network. 1 Turn on the computer and projector. 2 Launch a web browser, enter " - Canon REALiS WUX6000 Pro AV | User Manual - Page 192
is displayed. (P186) Comment Shows notes, such as where the projector is installed. (P186) Refresh Refreshes the displayed contents with the most recent information. Power Turns projector power on or off. Input Select an input signal and click [Apply] to change to that input signal. (P39 - Canon REALiS WUX6000 Pro AV | User Manual - Page 193
Maintenance Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Other Information Index 193 - Canon REALiS WUX6000 Pro AV | User Manual - Page 194
. • Never use volatile cleaning liquid or benzine, as these may damage the finish of the projector. • When using a chemical dust cloth, make sure to read the instructions thoroughly. • When cleaning the projector's lens, use a commonly available air blower or lens cleaning paper. The lens surface is - Canon REALiS WUX6000 Pro AV | User Manual - Page 195
Installation and Maintenance Maintenance Cleaning the Projector and the Air Filter • If the air filter cleaning screen is displayed when turning on the projector after cleaning the air filter, select [Yes] and press the OK button. The air filter counter is reset, and the message is no longer - Canon REALiS WUX6000 Pro AV | User Manual - Page 196
from the frame. Air filter Air filter 4 Install a new air filter into the frame. First holding the air filter, all the way into the projector. Air filter frame • Handle the air filter carefully. filter. • Contact the Canon Customer Support Center for further information. • Replacement air filter - Canon REALiS WUX6000 Pro AV | User Manual - Page 197
Installation and Maintenance Maintenance Replacing the Lamp When the usage time of the lamp exceeds a certain amount of time, the following message (two types) is displayed for 10 seconds every time the projector is turned on. 2,700 hours to less than 3,000 hours Prepare a new lamp when this screen - Canon REALiS WUX6000 Pro AV | User Manual - Page 198
on, the lamp may be broken. In this case, never attempt to replace the lamp by yourself. Always request service from the Canon Customer Support Center. Additionally, with ceiling-mounted projectors, the lamp may fall out when you open the lamp cover or while you are attempting to replace it. During - Canon REALiS WUX6000 Pro AV | User Manual - Page 199
Installation and Maintenance Maintenance Replacing the Lamp Replacing the Lamp 1 Turn off the projector power and remove the power plug. 2 Loosen one screw and open the lamp cover in the direction of the arrow. The lamp cover screw is - Canon REALiS WUX6000 Pro AV | User Manual - Page 200
Replacing the Lamp 7 Select [Reset] > [Yes] to reset the lamp counter. • It is recommended that you also replace the air filter when you replace the lamp. • Contact the Canon Customer Support Center for further information. • Replacement air filter part no.: RS-FL01 200 - Canon REALiS WUX6000 Pro AV | User Manual - Page 201
Appendix Appendix Installation and Maintenance Operation Appendix Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Other Information Index 201 - Canon REALiS WUX6000 Pro AV | User Manual - Page 202
problem is inside the projector, check whether the projector is installed and operating normally, unplug the projector from the power outlet to cool down the projector again, there may be a malfunction in the projector. Contact the Canon Customer Support Center. WARNING and Faulty lamp LAMP are lit. - Canon REALiS WUX6000 Pro AV | User Manual - Page 203
Troubleshooting LED indicator status WARNING (only) flashes 5 times repeatedly. projector again. Contact the Canon Customer Support Center if the same warning occurs again. The air filter is not installed. Check whether or not the air filter is installed correctly. Contact the Canon Customer Support - Canon REALiS WUX6000 Pro AV | User Manual - Page 204
Troubleshooting The lens connector is not attached correctly. The air filter is not installed correctly. Key lock is enabled. The lens cable is not connected to the lens unit correctly. Unplug the projector, connect the lens cable to the lens unit correctly, and then plug the projector in again. - Canon REALiS WUX6000 Pro AV | User Manual - Page 205
Troubleshooting model of notebook computer. For more detailed information, refer to the manual that came with your computer. Check whether the dual screen (multi the LAN cable (shielded twisted pair) is connected to the projector correctly. (P164) Network connections are not available until about 40 - Canon REALiS WUX6000 Pro AV | User Manual - Page 206
Troubleshooting ■ The Projected Image Is Blurred Cause The image is out of focus. The distance to the screen is too short. The projector is not placed straight in front of the screen. The projector has been moved to a place where the temperature varies a lot. The lens is stained. The tracking is - Canon REALiS WUX6000 Pro AV | User Manual - Page 207
Troubleshooting ■ You Cannot Project an instructions on "Precautions on the lamp" (P21). Check whether the operating temperature is between 0°C (32°F) and 40°C (104°F). (P24) Projector settings must be adjusted when using the projector at altitudes of 2,300 m (7,545.8') or higher. In the [Install - Canon REALiS WUX6000 Pro AV | User Manual - Page 208
Troubleshooting ■ You Cannot Operate the Remote Control Cause Batteries are not installed properly or they have run out. You are operating the remote control from the outside of the remote control operating range. There is an obstacle between the projector and the remote control. You are operating - Canon REALiS WUX6000 Pro AV | User Manual - Page 209
Relationship between Aspect and Screen Aspect This section describes the relationship between screen aspect (P48) and aspect (P52). Select an optimum aspect ratio of the projected image (screen aspect) or an optimum screen mode (aspect) according to the aspect ratio of the screen, type of input - Canon REALiS WUX6000 Pro AV | User Manual - Page 210
Relationship between Aspect and Screen Aspect ■ When the image is projected on a 16:9 screen Aspect ratio of connected device (16:10) 1920 x 1200 1440 x 900 1280 x 800 (16:9) 1920 x 1080 1280 x 720 (4:3) 1600 x 1200 1400 x 1050 640 x 480 Screen aspect setting (P48) [16:9] [16:9 D. image shift] - Canon REALiS WUX6000 Pro AV | User Manual - Page 211
Relationship between Aspect and Screen Aspect ■ When projecting on a 16:10 screen in the aspect ratio of the connected device Aspect ratio of connected device (16:10) 1920 x 1200 1440 x 900 1280 x 800 Screen aspect setting (P48) Aspect setting (P52) [16:10] [Auto] Screen image (16:9) 1920 x - Canon REALiS WUX6000 Pro AV | User Manual - Page 212
Relationship between Aspect and Screen Aspect ■ When projecting on a 4:3 screen in the aspect ratio of the connected device Aspect ratio of connected device (16:10) 1920 x 1200 1440 x 900 1280 x 800 Screen aspect setting (P48) Aspect setting (P52) [Auto] Screen image (16:9) 1920 x 1080 1280 x - Canon REALiS WUX6000 Pro AV | User Manual - Page 213
Test Patterns To access the test pattern menu, from the [Install settings] menu, select [Test pattern] > [On]. While the is shown during test pattern display that identifies the current test pattern and provides operating instructions. The following test patterns can be displayed. Use [ ] / [ ] - Canon REALiS WUX6000 Pro AV | User Manual - Page 214
Signal Types This projector supports the following signal types. If your computer or AV equipment is compatible with any one of these signal types, the projector's Auto PC function selects the input signal type to project an image appropriately. Analog PC Resolution (dots) 640 x 480 720 x 480 - Canon REALiS WUX6000 Pro AV | User Manual - Page 215
883 65.290 59.954 74.038 59.950 Connecting with AV equipment Signal type 480p 576p 720p 1080i 1080p Horizontal frequency (kHz in the table above are subject to change without notice. * This projector does not support any computer output signal with a dot clock of higher than 162 MHz - Canon REALiS WUX6000 Pro AV | User Manual - Page 216
Product Specifications Projection lens (*1) Display device ■ Projector Model name Display system WUX6000 RGB liquid crystal system Optical system Color separation by dichroic mirror / polarizing beam splitter and color composition by prism Type Size / Aspect ratio Drive system - Canon REALiS WUX6000 Pro AV | User Manual - Page 217
Specifications Model name WUX6000 Digital PC , PC cable, User's Manual (this manual), Supplement NMPJ Ver. 1.1 User's Manual (CD-ROM), Important Information to the characteristics of the LCD panel. * Using the projector continuously for an extended period of time may accelerate the deterioration - Canon REALiS WUX6000 Pro AV | User Manual - Page 218
Product Specifications ■ Specification of Each Lens Unit (Option) Name Standard Zoom Lens Long Zoom Lens Model number RS-IL01ST RS-IL02LZ External View Focal length F number Width Height Length Weight Zoom ratio Projection distance Size 100 projection distance 23.0 - 34.5 mm (0.9 - 1.4'') - Canon REALiS WUX6000 Pro AV | User Manual - Page 219
Name Model number Short Fixed Lens RS-IL03WF Product Specifications Ultra Long Zoom Lens RS-IL04UL External View Focal length F number Width Height Length Weight Zoom ratio Projection distance Size 100 projection distance Name Model number 12.8 mm (0.5'') 2.0 97.4 mm (3.8'') 106.5 mm (4.2'') - Canon REALiS WUX6000 Pro AV | User Manual - Page 220
Product Specifications ■ External View WUX6000 91 mm (3.6') 170 mm (6.7') 92 mm (3.6') 430 mm (16.9') 380 mm (15.0') Bolt holes (M4 x 6) for installation of ceiling attachment 128 mm (5.0') 234.5 mm (9.2') 53 mm (2.1') 212 mm (8.35') 150 mm (5.9') 141.5 mm (5.6') 154.5 mm (6.1') 311 mm (12 - Canon REALiS WUX6000 Pro AV | User Manual - Page 221
Pin No. Signal 9 +5 V power 10 Ground (Vertical sync.) 11 Ground 12 DDC data 13 Horizontal sync. 14 Vertical sync. 15 DDC clock ■ Service Port (CONTROL) Pin assignment Pin No. Signal 1 OPEN 2 RxD 3 TxD 4 OPEN 5 GND 6 OPEN 7 Internal pull-up 8 OPEN 9 OPEN Communication format - Canon REALiS WUX6000 Pro AV | User Manual - Page 222
Product Specifications Control commands Commands Power on Power supply Power off Power status acquisition HDMI Digital PC Analog PC-1 Input source Analog PC-2 Component LAN USB Input source acquisition Standard Presentation VividPhoto Photo/sRGB Dynamic Video Image Mode Cinema User 1 User 2 - Canon REALiS WUX6000 Pro AV | User Manual - Page 223
Product Specifications Commands ASCII representation Brightness acquisition GET=BRI Sharpness Sharpness value setting SHARP= Sharpness acquisition GET=SHARP Contrast Contrast value setting CONT= Contrast acquisition GET=CONT Auto ASPECT=AUTO 4:3 - Canon REALiS WUX6000 Pro AV | User Manual - Page 224
39, 133 DVI-I 132, 133 DVI-I input terminal 36 Dynamic gamma 91 E Edge blending 154 Electronic zoom 143 F Factory defaults 111 FREEZE 62 G Gamma 87 Guide 149 H HDMI 39, 134, 135 HDMI color space 79 HDMI IN terminal 36, 134, 135 HDMI input level 79 HDMI over scan 80 Horizontal pixels - Canon REALiS WUX6000 Pro AV | User Manual - Page 225
112 INPUT 40 Input signal select 39 Input terminal 36 Connecting to AV equipment ......... 135 Connection to computer 132 K Key lock 101 KEYSTONE 54 38, 60 Power saver settings 59 Power-saving 59 Progressive 80 Projector on 98 R Rear projection 141 Register network password 167 Register - Canon REALiS WUX6000 Pro AV | User Manual - Page 226
Index T TCP/IP settings 169 Test pattern 153, 213 Total dots 77 Tracking 77 True size (Aspect 53 Turning on external monitor output (preparing the notebook computer 140 U USB 65 USB Port 36 V Vertical pixels 78 Vertical position 78 VOL 63 W WARNING indicator 34, 202 Z Zooming an Image - Canon REALiS WUX6000 Pro AV | User Manual - Page 227
* • Air filter Part No.: RS-FL01 • Remote control Part No.: RS-RC04 • Remote control Part No.: RS-RC05 * Use the above materials to hang the projector from the ceiling. For details, refer to the assembly and installation manual provided with the ceiling attachment RS-CL11. 227 - Canon REALiS WUX6000 Pro AV | User Manual - Page 228
Menu Configuration Input Settings Menu *: Factory defaults (setting after reset) Aspect Digital PC / Analog PC-1/2 / HDMI (when [HDMI In] is [Computer]) P75 Auto* 16:10 16:9 4:3 True size HDMI (when [HDMI In] is [Auto]) / Component Auto* 16:9 4:3 Zoom True size USB / LAN Auto Auto - Canon REALiS WUX6000 Pro AV | User Manual - Page 229
Slideshow interval Split screen Off* On Settings Menu Configuration USB P81 [--:--] : [60:00] Digital PC / Analog PC-1/2 / HDMI / Component / LAN / USB P82 Split screen Control rights Swap right-left Layout Off On Left screen Right screen Mode 3-7 Mode 5-5 Mode 7-3 Image Adjustment Menu - Canon REALiS WUX6000 Pro AV | User Manual - Page 230
Menu Configuration Advanced adjustment Ambient light (when Photo/sRGB is selected) Random noise reduction MPEG noise reduction Off* P89 Adjust Type Tungsten Fluorescent Level L H Digital PC / Analog PC-1/2 / HDMI / Component P90 Off* Weak Middle Strong Digital PC / Analog PC-1/2 / HDMI / - Canon REALiS WUX6000 Pro AV | User Manual - Page 231
Install Settings Menu Positional lock Image flip H/V Screen aspect Zoom (Short Fixed Lens) Keystone Digital image shift Professional settings Micro-digital image shift Registration Fan mode - Canon REALiS WUX6000 Pro AV | User Manual - Page 232
Menu position Guide Show input status Overheat warning display Menu display time Lamp warning display Air filter warning display Split screen ID display Test pattern System Settings Menu User screen settings Logo capture Logo position No signal screen Screen when blank Projector on Load position - Canon REALiS WUX6000 Pro AV | User Manual - Page 233
Power management mode Power management duration Direct power on Beep Key repeat Key lock Remote control channel Motion blur reduction Language Other settings Password settings Register password [Fn] button settings Menu Configuration Disabled Lamp off Standby* 5 min. 10 min. 15 min.* 20 min. 30 - Canon REALiS WUX6000 Pro AV | User Manual - Page 234
Menu Configuration Audio in terminal select HDMI Digital PC Analog PC-1 Analog PC-2 Component LAN USB Gamma restore HDMI In Lamp counter Air filter counter Firmware Factory defaults Network Settings Menu Network settings lock Network password setting Register network password Network standby - Canon REALiS WUX6000 Pro AV | User Manual - Page 235
AMX Device Discovery Crestron RoomView Information Model name Input signal Firmware Serial no. IP address E-mail sender address E-mail recipient address Projector name Comments System information ID Menu Configuration Off* P168 On P168 P168 P168 Off* On IP address Subnet mask Gateway address - Canon REALiS WUX6000 Pro AV | User Manual - Page 236
Schweiz AG Geschäftsbereich Wiederverkauf, Industriestrasse 12, CH-8305 Dietlikon, Switzerland CANON GMBH Zetschegasse 11, A-1230 Wien, Austria CANON España, S.A. Av. De Europa, 6 Alcobendas 28108 Madrid, Spain CANON PORTUGAL S.A. Rua Alfredo da Silva, 14 Alfragide 2610-016 Amadora, Portugal CANON
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
 |
 |
Table of Contents
Safety Instructions
Before Use
Operation
Projecting an Image
Useful Functions Available
During a Presentation
Setting Functions from
Menus
Installation and Maintenance
Installation
Connecting to a Network
Maintenance
Appendix
Other Information
Index
ENG
MULTIMEDIA PROJECTOR
User’s Manual