Canon imageFORMULA R50 User Manual - Page 82

SNMP Setting, Community Setting, Description, Default Value

Get Canon imageFORMULA R50 PDF manuals and user guides View all Canon imageFORMULA R50 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Item mDNS Description Default Value Enable/disable multicast DNS. This setting allows scanning applications to search for and automatically connect to the scanner. This is normally enabled. ON When the setting is disabled, you must manually specify the scanner using its assigned IP address to scan from the scanning application. SNMP Setting If you click [SNMP Setting] on the Device Configuration screen, the page below is displayed. Item Security Auth trap SNMP v1 Community Setting SNMP v3 User Setting Description Default Value Sets the SNMP authentication trap function to enabled/disabled. By setting this to [ON], if an SNMP request is received from a community that is not registered in [Community Setting], then a message is sent to the trap destination. OFF Sets the SNMP v1 support function to enabled/disabled. OFF Moves to the [Community Setting] screen. - Sets the SNMP v3 support function to enabled/disabled. OFF Moves to the [User Setting] screen. - Community Setting In the SNMP settings screen, enable SNMP v1 and click [Community Setting] to open the page shown in the following diagram. Item SNMP Service Location Description Sets the SNMP function to enabled/disabled. Input the location where the scanner is installed. Default Value OFF None 82

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
82
SNMP Setting
If you click [SNMP Setting] on the Device Configuration screen, the
page below is displayed.
Community Setting
In the SNMP settings screen, enable SNMP v1 and click [Community
Setting] to open the page shown in the following diagram.
Item
Description
Default Value
mDNS
Enable/disable multicast DNS.
This setting allows scanning
applications to search for and
automatically connect to the
scanner.
This is normally enabled.
When the setting is disabled, you
must manually specify the scanner
using its assigned IP address to
scan from the scanning
application.
ON
Item
Description
Default Value
SNMP
Service
Sets the SNMP function to
enabled/disabled.
OFF
Location
Input the location where the
scanner is installed.
None
Security -
Auth trap
Sets the SNMP authentication trap
function to enabled/disabled. By
setting this to [ON], if an SNMP
request is received from a
community that is not registered in
[Community Setting], then a
message is sent to the trap
destination.
OFF
SNMP v1
Sets the SNMP v1 support function
to enabled/disabled.
OFF
Community
Setting
Moves to the [Community Setting]
screen.
-
SNMP v3
Sets the SNMP v3 support function
to enabled/disabled.
OFF
User Setting
Moves to the [User Setting] screen.
-
Item
Description
Default Value