Canon imagePROGRAF iPF770 Setup Guide
Canon imagePROGRAF iPF770 Manual
 |
View all Canon imagePROGRAF iPF770 manuals
Add to My Manuals
Save this manual to your list of manuals |
Canon imagePROGRAF iPF770 manual content summary:
- Canon imagePROGRAF iPF770 | Setup Guide - Page 1
paper, ink tanks, and the printhead. Electronic Manuals Basic Guide The Basic Guide describes the following information. • Loading paper, Replacing the consumables, Control Panel menus, and others • Troubleshooting tips and Error messages • Preparations for transferring the printer User's Guide - Canon imagePROGRAF iPF770 | Setup Guide - Page 2
printer. 3 Three people should hold the printer's carrying handles and place the printer on a table or other flat location. • The iPF770 Series the printer, may cause damage to the printer. 5 Move the printer to the location where you will use it. • When moving the stand, lift the support rod - Canon imagePROGRAF iPF770 | Setup Guide - Page 3
tank installation are shown on the display screen. As instructed, grab the handle on the ink tank cover to open it. 5 While pressing the stopper of the ink tank lock lever inwards, open the ink tank lock lever upwards. 6 Shake the ink tanks gently 1 to 2 times before opening the pouch. 7 Open - Canon imagePROGRAF iPF770 | Setup Guide - Page 4
top cover. The carriage (a) moves to the position shown in the figure. Instructions on printhead attachment are shown on the display screen. 2 Pull the printhead the printhead into the carriage (b) 6 with the ink holes (a) facing away from the printer as shown in the figure. Carefully push the - Canon imagePROGRAF iPF770 | Setup Guide - Page 5
of this time by referring to "Install the Software" on page 7 to install the software on your PC. • Charging the system with ink fills the system MEMO from the ink tanks to the printhead. In addition, cleaning is performed to keep the printer in optimal condition. This may cause the remaining - Canon imagePROGRAF iPF770 | Setup Guide - Page 6
10 Pull the release lever forward. Printer setup is now complete. • The method for loading roll paper is given MEMO in the User's Guide, Basic Guide, and the control panel navigation function, which can be accessed using the procedure in "How to Display the Electronic Manuals" (P.14). Follow the - Canon imagePROGRAF iPF770 | Setup Guide - Page 7
Install the software • Use a USB cable that conforms to the Hi-Speed USB specification. • Connect the USB cable to the printer according to the on-screen instructions during installation of the printer driver. If you connect the USB cable before installing the printer driver, the printer driver may - Canon imagePROGRAF iPF770 | Setup Guide - Page 8
After reviewing the installation results in the Complete Installation window, click Next. 13 In the Finish window, select Restart my computer now and click Restart. • Be careful not to insert the USB cable into the LAN port. For TCP/IP (network) connections Install the software • If the printer - Canon imagePROGRAF iPF770 | Setup Guide - Page 9
on the network After reading the precautions in the Getting Ready window, select Find available printers in the network and click Next. Proceed to step 6. When entering the printer's IP address manually After reading the precautions in the Getting Ready window, select Specify the IP address of - Canon imagePROGRAF iPF770 | Setup Guide - Page 10
in the network and click Next. When the IP Address Specifications window appears, follow the instructions of "When entering the printer's IP address manually" in step 8 to 11 on page 9 to complete the installation of the software. How to enter IP addresses MEMO 1. Press the and keys to select - Canon imagePROGRAF iPF770 | Setup Guide - Page 11
on your computer environment. OS X v10.6.8 to v10.9 Install the software • If you install the software, log onto the computer as an administrator. 1 After making sure the printer is not connected to the computer, turn the computer on. Insert the provided User - Canon imagePROGRAF iPF770 | Setup Guide - Page 12
. 16 Click Next. 19 Click Exit. • You can view a description of adding MEMO printers by clicking Help. • It may take a long time until the printer MEMO information is displayed on the screen. • You can also add the printer by specifying the IP address by selecting IP. 17 Select the Execute media - Canon imagePROGRAF iPF770 | Setup Guide - Page 13
Store Accessories in the Pockets 1 Use the manual pocket to store the manual so you can refer to it as needed. 2 When using the stand, store the 3-inch paper core attachment and other accessories in the accessory pocket. • The accessory pocket is included with the stand. MEMO 13 - Canon imagePROGRAF iPF770 | Setup Guide - Page 14
On Windows This section describes how to view the User's Guide and Paper Reference Guide from the printer driver. • You can also view each of the manuals by clicking the links to the MEMO product manuals from other installed software. 1 On Windows 7 and earlier Click the Control Panel from the - Canon imagePROGRAF iPF770 | Setup Guide - Page 15
Click Utility. 5 Click Open Printer Utility. 6 Click Support. 7 Click the User Manual button. 8 To display the user guide, click User's Guide. To display the Paper Reference Guide, click Paper Reference Guide. Viewing the Basic Guide The Basic Guide is stored on the User Software CD-ROM that is - Canon imagePROGRAF iPF770 | Setup Guide - Page 16
a problem with the printer, and the issue may be easily resolved. Common messages and the causes are listed here with corrective actions. For more information on other messages, refer to the User's Guide or Basic Guide. (See "How to Display the Electronic Manuals" on P.14) Message Check if ink tank
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
Setup Guide
ENG
Introductory Information
Series
Series
±
QT6-0555-V0±
PRINTED IN XXXXXXXX
XXXXXXXX
©CANON INC. 20±4
QT60555V01
Preparations
(P.2)
Install the Ink Tanks
(P.3)
Install the Printhead
(P.4)
(P.14)
Load Paper to Adjust the Printhead
(P.5)
Store Accessories in the Pockets
(P.13)
(P.7)
Install the Software
How to Display the Electronic
Manuals
Caution
Instructions in this Setup Guide show the iPF770 printer and printer stand ST-34. Note that your printer and printer stand may look
different from these illustrations in some cases. However, basic operations are the same.
•
300mm
10mm
600mm
(When using the stand)
600mm
(When not using
the stand)
200mm
200mm
i
j
k
d
c
e
f
g
b
l
h
a
Details for each step are given in this Setup Guide. Simply follow the instructions
to install the printer.
If an error message is displayed during setup or other problems occur, refer to
"Responding to Messages" on page ±6.
Introduction
Printer
Installation space (W x D x H mm)
iPF670 Series (*±)
Without stand
±397 × ±308 × 807
Stand ST-27
±397 × ±700 × ±362
Overview of Setup
Space Required for Installation
Read this manual before attempting to operate the printer.
Keep this manual in a handy location for future reference.
iPF770 Series
MEMO
Printer
a.
c.
Roll holder:
Already attached to printer
d.
3-inch paper core attachment R
e. Printhead
f.
Starter ink tanks (for first-time installation)
C, M, Y, MBK x2, BK
g. Included paper
Package Contents
Some items are included with the printer but not described in this manual.
Keep these items in a safe place after setup because they are used in
various printing applications.
•
For instructions on the included items not described in this manual, refer to
the User's Guide.
•
A cable to connect the printer to a computer is not provided with the printer.
•
h. Setup Guide (this document)
i.
Set of printer documentation
j.
Set of CD-ROMs
k.
Power cord
b.
3-inch paper core attachment L
The Manuals Supplied with This Printer
• Canon, the Canon logo, and imagePROGRAF are trademarks or registered trademarks of CANON
INC.
• Microsoft is a registered trademark of Microsoft Corporation.
• Windows is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or other
countries.
• Windows Vista is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or
other countries.
• Mac, Mac OS, OS X and Bonjour are trademarks of Apple Inc., registered in the U.S. and other
countries.
• All other trademarks or registered trademarks described in this Setup Guide are the property of
their respective owners.
Even if you do not use the printer driver, be sure to install
Media
Configuration Tool
from the provided User Software CD-ROM. With
Media Configuration Tool
, the paper types that are available in your
area can be registered to the printer. For instructions on installation,
refer to "Install the Software" on page 7. (In Windows, select
Install
Individual Software
in the
Setup Menu
window to install
Media
Configuration Tool
only.)
•
A space larger than the following dimensions needs to be allocated when
setting up this printer.
±397 × ±480 × ±362
*±: A stand is optional for the iPF670 series. (It may be included as a
standard accessory in some locations.)
*2: The stands that are available differ between regions.
After installing the printer as shown in this Setup Guide, refer to the
manuals for instructions on operation and maintenance.
Printed Manuals
Quick Guide
The Quick Guide contains information such as warnings for using this
product safely and how to operate the navigation that is useful when
replacing paper, ink tanks, and the printhead.
Electronic Manuals
Basic Guide
The Basic Guide describes the following information.
• Loading paper, Replacing the consumables, Control Panel menus, and others
• Troubleshooting tips and Error messages
• Preparations for transferring the printer
User's Guide
This guide describes advanced usage of the printer such as paper saving tips,
how to print a poster and banner with the supplied software and print quality
adjusting method, in addition to the basic instructions for printing on roll paper or
cut sheet.
Paper Reference Guide
This guide describes about the types and specifications of the available media on
the printer.
To refer to the electronic manuals Refer to "How to Display the Electronic
Manuals" (P.±4)
l.
Set of stands
(iPF770 series only)
A stand is optional for the iPF670 series. (It may be included as a standard
accessory in some locations.)
•
First, the stand needs to be assembled.
Refer to the Stand Setup Guide included with the stand for details on how
to assemble the stand.
Note that a stand is optional for the iPF670 series.
Stand ST-26
±704 × ±700 × ±362
Stand ST-34
±704 × ±480 × ±362
Stand ST-33
Stand used (*2)