Canton DM 20 Owners Manual - Page 34

Setting up the remote control, Using the remote control

Get Canton DM 20 PDF manuals and user guides View all Canton DM 20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Setting up the remote control Insert the batteries supplied into the remote control. Be careful to insert them the correct way up according to the polarity markings (+/-). Using the remote control When all devices are connected to each other and the power has been switched on the Canton DM goes into Standby mode. Press any key to activate the remote control. If the remote control is not used for longer than 30 seconds it goes into idle mode. Press any key to reactivate it. Note: When the device is turned on for the first time it starts the initial installation process automatically (see page 36). If the display shows "keine Verbindung" then there is no radio connection between the remote control and the DM System. Check that the DM System is switched on and connected to the mains power supply or reduce the distance between the remote control and the DM System. Operating the DM System Press to start the DM System. If you want to turn the DM System off again press again. The DM System will go back into Standby mode. Note: If the DM System is disconnected from the mains power supply when it is still switched on it will automatically go back into an active state when it is reconnected to the mains power supply (e.g. via a master or slave multiple socket lead). 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
34
Operating the DM System
Press
to start the DM System.
If you want to turn the DM System off again press
again. The DM System will go back into Standby
mode.
Setting up the remote control
Insert the batteries supplied into the remote control. Be careful to insert them the correct way up according to the polarity markings (+/-).
Using the remote control
When all devices are connected to each other and the power has been switched on the
Canton DM goes into Standby mode. Press any key to activate the remote control. If
the remote control is not used for longer than 30 seconds it goes into idle mode. Press
any key to reactivate it.
Note: When the device is turned on for the first time it starts the initial installation
process automatically (see page 36).
If the display shows “keine Verbindung” then there is no radio connection between
the remote control and the DM System. Check that the DM System is switched on
and connected to the mains power supply or reduce the distance between the remote
control and the DM System.
Note: If the DM System is disconnected from the mains power supply when it is still switched on it will automatically go back into an active state
when it is reconnected to the mains power supply (e.g. via a master or slave multiple socket lead).