Casio CTK-800 User Guide - Page 38

Finishing with an Ending Pattern, Using One-touch Preset

Get Casio CTK-800 PDF manuals and user guides View all Casio CTK-800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Auto Accompaniment To use synchro start 1 Press the SYNCHRO/ENDING button to put the keyboard into synchro start standby. Flash 2 Playing a chord and the rhythm pattern starts to play automatically. NOTE • If the MODE switch is set to NORMAL, only the rhythm plays (without a chord) when you play on the accompaniment keyboard. • If you press the INTRO button before playing anything on the keyboard, the rhythm starts automatically with an intro pattern when you play something on the accompaniment keyboard. • Pressing the VARIATION/FILL-IN button before playing anything on the keyboard causes play to start with the variation pattern when something is played on the keyboard. • To cancel synchro start standby, press the SYNCHRO/ ENDING button one more time. Finishing with an Ending Pattern You can end your performances with an ending pattern that brings the rhythm pattern you are using to a natural-sounding conclusion. The following procedure describes how to insert an ending pattern. Note that the actual ending pattern played depends on the rhythm pattern you are using. To finish with an ending pattern 1 While the rhythm is playing, press the SYNCHRO/ ENDING button. • This causes the ending pattern to play, which brings rhythm accompaniment to an end. NOTE • The timing when the ending pattern starts depends on when you press the SYNCHRO/ENDING button. If you press the button before the second beat of the current measure, the ending pattern starts playing immediately. Pressing the button at any point in the measure after the second beat results in the ending pattern playing from the beginning of the following measure. Using One-touch Preset One-touch preset automatically makes the settings listed below in accordance with the rhythm pattern you are using. • Keyboard tone • Layer, Split, or Layer Split on/off • Layered tone (when layer is turned on), split tone (when split is turned on), or layered split tone (when layer and split are turned on) • Tempo • Reverb and chorus settings To use one-touch preset 1 Select the rhythm you want to use. 2 Use the MODE switch to select the accompaniment mode you want to use. 3 Press the ONE TOUCH PRESET button. • This automatically configures the one-touch preset settings in accordance with the rhythm you selected, and enters synchro start standby. 4 Play a chord. This will cause the rhythm pattern to start to play automatically. • Accompaniment is played using the one touch preset settings. E-36 706A-E-038A

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
E-36
To use synchro start
1
Press the SYNCHRO/ENDING button to put the
keyboard into synchro start standby.
2
Playing a chord and the rhythm pattern starts to
play automatically.
NOTE
•
If the MODE switch is set to NORMAL, only the rhythm
plays (without a chord) when you play on the
accompaniment keyboard.
•
If you press the INTRO button before playing anything
on the keyboard, the rhythm starts automatically with
an intro pattern when you play something on the
accompaniment keyboard.
•
Pressing the VARIATION/FILL-IN button before playing
anything on the keyboard causes play to start with the
variation pattern when something is played on the
keyboard.
•
To cancel synchro start standby, press the SYNCHRO/
ENDING button one more time.
Finishing with an Ending Pattern
You can end your performances with an ending pattern that
brings the rhythm pattern you are using to a natural-sounding
conclusion.
The following procedure describes how to insert an ending
pattern. Note that the actual ending pattern played depends
on the rhythm pattern you are using.
To finish with an ending pattern
1
While the rhythm is playing, press the SYNCHRO/
ENDING button.
•
This causes the ending pattern to play, which brings
rhythm accompaniment to an end.
NOTE
•
The timing when the ending pattern starts depends on
when you press the SYNCHRO/ENDING button. If you
press the button before the second beat of the current
measure, the ending pattern starts playing immediately.
Pressing the button at any point in the measure after
the second beat results in the ending pattern playing
from the beginning of the following measure.
Auto Accompaniment
706A-E-038A
Using One-touch Preset
One-touch preset automatically makes the settings listed
below in accordance with the rhythm pattern you are using.
•
Keyboard tone
•
Layer, Split, or Layer Split on/off
•
Layered tone (when layer is turned on), split tone (when
split is turned on), or layered split tone (when layer and
split are turned on)
•
Tempo
•
Reverb and chorus settings
To use one-touch preset
1
Select the rhythm you want to use.
2
Use the MODE switch to select the accompaniment
mode you want to use.
3
Press the ONE TOUCH PRESET button.
•
This automatically configures the one-touch preset
settings in accordance with the rhythm you selected,
and enters synchro start standby.
4
Play a chord. This will cause the rhythm pattern to
start to play automatically.
•
Accompaniment is played using the one touch preset
settings.
Flash