Casio XJ-ST145 User Guide - Page 55

Using Wired LAN to Control the Projector (XJ-H1650, XJ-ST145, Supported External Devices

Get Casio XJ-ST145 PDF manuals and user guides View all Casio XJ-ST145 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Using Wired LAN to Control the Projector (XJ-H1650, XJ-ST145, XJ-ST155) The projector can be controlled by a computer or other external device by connecting the device to the projector's LAN port. Supported External Devices This projector supports all commands of PJLink Class1 (Version 1.00). http://pjlink.jbmia.or.jp/english/ This projector is supported by the commands of the Crestron Electronics controller and software (RoomView®). http://www.crestron.com/ This projector is supported by AMX Device Discovery. http://www.amx.com/ Information about the types of external devices that can be connected to the LAN port and control the projector, as well as the control commands supported for each external device will be published on the CASIO website below as such information becomes available. http://www.casio.com/support/ Controlling the Projector from a Computer When the projector is linked to a computer over a wired or wireless LAN connection, you can use the computer's Web browser to access a Wireless Presentation System control panel to control the projector. To establish a wired LAN connection between the projector and a computer 1. Connect the LAN port of the projector to the LAN hub or other network devices to which the computer is connected. Projector Computer LAN hub z In a configuration like the one in the illustration above, you should normally use straight type LAN cables. If you are connecting the projector's LAN port directly to the LAN port of a computer, use a cross type LAN cable. 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
55
The projector can be controlled by a computer or other external device by connecting the device to
the projector’s LAN port.
Supported External Devices
This projector supports all commands of PJLink Class1 (Version 1.00).
This projector is supported by the commands of the Crestron Electronics controller and software
(RoomView
®
).
This projector is supported by AMX Device Discovery.
Information about the types of external devices that can be connected to the LAN port and control the
projector, as well as the control commands supported for each external device will be published on
the CASIO website below as such information becomes available.
Controlling the Projector from a Computer
When the projector is linked to a computer over a wired or wireless LAN connection, you can use the
computer’s Web browser to access a Wireless Presentation System control panel to control the
projector.
To establish a wired LAN connection between the projector and a computer
1.
Connect the LAN port of the projector to the LAN hub or other network devices
to which the computer is connected.
In a configuration like the one in the illustration above, you should normally use straight type
LAN cables. If you are connecting the projector’s LAN port directly to the LAN port of a
computer, use a cross type LAN cable.
Using Wired LAN to Control the Projector
(XJ-H1650, XJ-ST145, XJ-ST155)
Projector
Computer
LAN hub